Yamaha LZ300C Скачать руководство пользователя страница 24

Страница: 24 / 84

Basic components

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 49.

EMU26490

Digital tachometer

The tachometer shows the engine speed
and has the following functions.

NOTE:

All segments of the display will light momen-
tarily after the main switch is turned on and

will return to normal thereafter.

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 26.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

1. Flushing device

ZMU01951

ZMU01865

ZMU01866

1. Tachometer
2. Trim meter
3. Hour meter
4. Oil level indicator
5. Overheat warning indicator
6. Set button
7. Mode button

ZMU01891

Содержание LZ300C





















































































Результаты поиска

Содержание LZ300C

Отзывы:

Похожие инструкции для LZ300C

Бренды по названию

Популярные бренды

Yamaha LZ300C, Руководство пользователя

Результаты поиска

Содержание LZ300C

Отзывы:

Похожие инструкции для LZ300C

Бренды по названию

Популярные бренды