Yamaha LZ300C Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 84

background image

Operation

37

possible to start the engine. The starter
can also be damaged. If the engine will
not start after 5 seconds of cranking,
return the main switch to “

” (on), wait

10 seconds, then crank the engine

again.

EMU27670

Warming up engine

EMU27701

Electric start and prime start models

1.

After starting the engine, allow it to idle
for 3 minutes to warm up. Failure to do
so will shorten engine life.

2.

Check for a steady flow of water from the
cooling water pilot hole.

CAUTION:

ECM00510

A flow of water from the hole on the ex-
haust cover shows that the water pump is
pumping water through the cooling pas-
sages. If water is not flowing out of the

hole at all times while the engine is run-
ning, overheating and serious damage
could occur. Stop the engine and check
whether the cooling water inlet on the
lower case or the cooling water pilot hole
is blocked. Consult your Yamaha dealer if
the problem cannot be located and cor-

rected.

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the

engine idles (or runs at low speeds).

EMU27760

Forward (tiller handle and remote
control models)

If equipped tiller control:
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and
firmly from neutral to forward.

If equipped Remote control:

ON

START

OFF

ZMU01881

ZMU01882

«
...
40
41
42
43
44
...
»

Содержание LZ300C





















































































Отзывы:

Нет отзывов

Похожие инструкции для LZ300C

Бренд: Xilinx Страницы: 14

Бренд: Gigabyte Страницы: 100

Бренд: Biostar Страницы: 72

Бренд: Gigabyte Страницы: 44

Бренд: Ublox Страницы: 38

Fatality H97 Killer series

Бренд: ASROCK Страницы: 109

ADIS1650 PCBZSeries

Бренд: Analog Devices Страницы: 11

Бренд: Texas Instruments Страницы: 21

Voltage Supervisor SOT23

Бренд: Microchip Technology Страницы: 28

Supero X9DRW-7TPF

Бренд: Supero Страницы: 119

FIERCE 2 54LB/48

Бренд: Watersnake Страницы: 44

Venom SXW 34/26

Бренд: Watersnake Страницы: 44

ADVANCE SWS 70/36

Бренд: Watersnake Страницы: 28

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 105

Бренд: TYAN Страницы: 67

Бренд: TYAN Страницы: 66

Бренд: DFI Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды