Yamaha LZ300C Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 84

background image

Basic components

24

port and starboard engines.

NOTE:

●

The fuel flow meter displays gallons/hour
or liters/hour according to operator prefer-
ence. Select the desired unit of measure-
ment by setting the selector switch on the
back of the gauge during installation.

●

The fuel consumption meter and fuel
economy meter will indicate the same unit

of measurement.

EMU26760

Fuel consumption meter

This gauge displays the total amount of fuel
consumed since the gauge was last reset.
Press the “

” (mode) button repeatedly

until the indicator on the face of the gauge
points to total “

” (total). To reset the total

fuel consumption to zero, press the “

”

(set) and “

” (mode) buttons at the same

time.

EMU26770

Fuel economy

This gauge displays the distance per liter or
gallon when cruising, and is only for refer-
ence use by the operator.
Press the “

” (mode) button repeatedly

until the indicator on the face of the gauge
points to “

” (economy).

NOTE:

If twin engines are installed on your boat, the
gauge will only display the total fuel economy

of both engines.

NOTE:

●

Fuel consumption varies greatly with boat
design, weight, propeller used, engine trim
angle, sea conditions (including wind), and
throttle position. Fuel consumption also
varies slightly with the type of water (salt,
fresh, and contaminate levels), air temper-
ature and humidity, cleanliness of the boat

1. Selector switch

ZMU01751

ZMU01752

«
...
27
28
29
30
31
...
»

Содержание LZ300C





















































































Отзывы:

Нет отзывов

Похожие инструкции для LZ300C

Fatal1ty Z170 Gaming K4 Series

Бренд: ASROCK Страницы: 163

Бренд: AOpen Страницы: 8

Бренд: Texas Instruments Страницы: 19

Бренд: QDI Страницы: 85

Airborne WLNN-EK-DP55x

Бренд: B&B Electronics Страницы: 6

Бренд: Fujitsu Siemens Computers Страницы: 42

Бренд: Gigabyte Страницы: 120

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

B85-IE35 Series

Бренд: MSI Страницы: 190

ISL70321SEHDEMO1Z

Бренд: Intersil Страницы: 9

JW-A880GMT-EXTREME

Бренд: J&W Страницы: 39

Бренд: Vector Страницы: 73

Бренд: Microchip Technology Страницы: 35

Бренд: Texas Instruments Страницы: 19

Бренд: IBASE Technology Страницы: 62

Бренд: Supermicro Страницы: 105

Бренд: EPOX Страницы: 64

Бренд: IEI Technology Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды