Yamaha F-20 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 104

background image

Maintenance

65

retor or the fogging hole of the silencer
cover, if equipped. When properly done,
the engine will smoke excessively and
almost stall.

11. Remove the outboard motor from the

test tank. For further details, see page
62.

12. Drain the cooling water completely out

of the motor. Clean the body thoroughly.

13. Install the silencer cover/cap and top

cowling.

EMU28402

Lubrication

1.

Install the spark plug(s) and torque to
proper specification. For information on
spark plug installation, see page 72.

2.

Change the gear oil. For instructions,
see page 77. Inspect the oil for the pres-
ence of water that indicates a leaky seal.
Seal replacement should be performed
by an authorized Yamaha dealer prior to
use.

3.

Grease all grease fittings. For further de-
tails, see page 71.

TIP:

For long-term storage, fogging the engine
with oil is recommended. Contact your
Yamaha dealer for information about fogging
oil and procedures for your engine.

EMU28423

Cleaning and anticorrosion
measures

1.

Wash down the exterior of the outboard
motor with fresh water and dry off com-
pletely.

NOTICE:

Do not spray water

into the air intake.

[ECM01840]

2.

Spray the outboard motor exterior with
“Yamaha Silicone Protectant”.

3.

Wax the cowling with a non-abrasive
wax such as “Yamaha Silicone Wax”.

EMU28443

Flushing power unit

Perform this procedure right after operation
for the most thorough flushing.

NOTICE

ECM01530

Do not perform this procedure while the
engine is running. The water pump may
be damaged and severe damage from

overheating can result.

1.

After shutting off the engine, unscrew
the garden hose connector from the fit-
ting on the bottom cowling.

2.

Screw the garden hose adapter onto a
garden hose, which is connected to a
fresh water supply, and then connect it
to the garden hose connector.

1. Fitting
2. Garden hose connector
3. Garden hose adapter

ZMU05556

1

3

2

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
69
70
71
72
73
...
»

Содержание F-20









































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20

Бренд: Sansui Страницы: 31

Бренд: Laney Страницы: 13

Бренд: Yamaha Страницы: 48

Бренд: dB Technologies Страницы: 133

Бренд: Yamaha Страницы: 24

Бренд: Viking Страницы: 4

Бренд: DaytonAudio Страницы: 2

Бренд: HR Страницы: 12

Бренд: Ultimate Страницы: 24

Бренд: Sansui Страницы: 30

Бренд: E&I Страницы: 9

Бренд: ESX Страницы: 20

L-RF-EDFA-14dBm

Бренд: Questtel Страницы: 16

Бренд: Albion Страницы: 12

Бренд: Omron Страницы: 2

Бренд: TRU Audio Страницы: 4

Reference Amplifier

Бренд: Genesis Страницы: 2

Бренд: Teledyne Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды