Yamaha F-20 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 104

background image

Maintenance

74

flushing attachment or test tank can be

used.

A diagnostic tachometer should be used for
this procedure. Results may vary depending
on whether testing is conducted with the
flushing attachment, in a test tank, or with the
outboard motor in the water.
1.

Start the engine and allow it to warm up
fully in neutral until it is running smooth-
ly.

TIP:

Correct idling speed inspection is only possi-
ble if the engine is fully warmed up. If not
warmed up fully, the idle speed will measure
higher than normal. If you have difficulty ver-
ifying the idle speed, or the idle speed re-
quires adjustment, consult a Yamaha dealer
or other qualified mechanic.
2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 13.

EMU29077

Changing engine oil

Change the engine oil several minutes after
the engine has been stopped, so that the oil
is still warm, but not hot.

WARNING

EWM01950

Be sure the outboard motor is securely

fastened to the transom or a stable stand.

NOTICE

ECM01710

Change the engine oil after the first 20
hours of operation or 3 months, and ev-
ery 100 hours or at 1-year intervals there-
after. Otherwise the engine will wear

quickly.

1.

Put the outboard motor in an upright po-
sition (not tilted).

NOTICE:

If the motor

is not level, the oil level indicated on

the dipstick may not be accurate.

[ECM01860]

2.

Prepare a suitable container that holds a
larger amount than the engine oil capac-
ity. Loosen and remove the drain screw
while holding the container under the
drain hole. Then remove the oil filler cap.
Let the oil drain completely. Wipe up any
spilled oil immediately.

3.

Put a new gasket on the oil drain screw.
Apply a light coat of oil to the gasket and
install the drain screw.

TIP:

If a torque wrench is not available when you
are installing the drain screw, finger tighten

1. Drain screw

Drain screw tightening torque:

28.0 Nm (2.86 kgf-m, 20.7 ft-lb)

ZMU05554

ZMU05561

1

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
78
79
80
81
82
...
»

Содержание F-20









































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20

Бренд: Gainlab Audio Страницы: 15

Renaissance Signature Mk II

Бренд: VAC Страницы: 12

Бренд: Gibson Страницы: 1

Бренд: Interface Devices Страницы: 8

EVID C8.2 Ceiling

Бренд: Electro-Voice Страницы: 2

Бренд: Ntron Страницы: 29

Бренд: Clavia Страницы: 13

Power Station 100

Бренд: Fryette Страницы: 12

Бренд: Ramsey Electronics Страницы: 44

Mobitronic ECL-100

Бренд: Waeco Страницы: 80

Бренд: Jas Audio Страницы: 5

Бренд: Yaesu Страницы: 132

Бренд: M-Audio Страницы: 21

Бренд: Signal Vehicle Products Страницы: 20

Бренд: RE Audio Страницы: 12

Бренд: Elcometer Страницы: 19

Бренд: Ecler essentials Страницы: 16

Бренд: zapco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды