Yamaha F-20 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 104

background image

62

Maintenance

EMU28226

Transporting and storing

outboard motor

WARNING

EWM00692

●

USE CARE when transporting fuel tank,
whether in a boat or car.

●

DO NOT fill fuel container to maximum
capacity. Gasoline will expand consid-
erably as it warms up and can build up
pressure in the fuel container. This can
cause fuel leakage and a potential fire

hazard.

WARNING

EWM01860

Leaking fuel is a fire hazard. When trans-
porting and storing the outboard motor,
close the fuel cock to prevent fuel from
leaking. Never get under the engine while
it is tilted. Severe injury could occur if the

outboard motor accidentally falls.

NOTICE

ECM00660

Do not use the tilt support lever or knob
when trailering the boat. The outboard
motor could shake loose from the tilt sup-
port and fall. If the motor cannot be trail-
ered in the normal running position, use
an additional support device to secure it

in the tilt position.

The outboard motor should be trailered and
stored in the normal running position. If there
is insufficient road clearance in this position,
then trailer the outboard motor in the tilt po-
sition using a motor support device such as
a transom saver bar. Consult your Yamaha
dealer for further details.

EMU32030

Dismounting the outboard motor

1.

Stop the engine and land the boat.

2.

Disconnect the fuel line from the out-
board motor.

3.

For electric start models, disconnect the
battery cables from the battery termi-
nals.

4.

To prevent steering movement, turn the
adjuster lever to “A”.

5.

Loosen the clamp screw(s).

6.

Hold the handgrips and steering brack-
ets as shown in the illustration and lift up
the outboard motor to dismount it from
the boat.

ZMU05632

A

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
66
67
68
69
70
...
»

Содержание F-20









































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20

Бренд: CANARY AUDIO Страницы: 10

MINAS-BL GP series

Бренд: Panasonic Страницы: 56

65 Princeton Reverb

Бренд: Fender Страницы: 2

Бренд: QUAD Страницы: 10

Бренд: QUAD Страницы: 29

Бренд: QUAD Страницы: 6

Бренд: Waltron Страницы: 11

Бренд: B&K Страницы: 15

Бренд: Laney Страницы: 4

Бренд: Wyred 4 Sound Страницы: 12

Бренд: JBL Страницы: 27

Бренд: HAMTRONICS Страницы: 3

Бренд: Galileo Страницы: 30

Бренд: DSM Страницы: 8

PX3-3000 series

Бренд: Raritan Страницы: 875

Custom Reverb 18

Бренд: Olsson Страницы: 8

Бренд: Oceanic Страницы: 9

Бренд: Sure Electronics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды