Yamaha F-20 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 104

background image

Operation

55

Bow Down

Too much trim-in causes the boat to “plow”
through the water, decreasing fuel economy
and making it hard to increase speed. Oper-
ating with excessive trim-in at higher speeds
also makes the boat unstable. Resistance at
the bow is greatly increased, heightening the
danger of “bow steering” and making opera-
tion difficult and dangerous.

TIP:

Depending on the type of boat, the outboard
motor trim angle may have little effect on the
trim of the boat when operating.

EMU27934

Tilting up and down

If the engine will be stopped for some time or
if the boat is moored in shallows, the out-
board motor should be tilted up to protect the
propeller and lower casing from damage by
collision with obstructions, and also to re-

duce salt corrosion.

WARNING

EWM00221

Be sure all people are clear of the out-
board motor when tilting up and down,
Body parts can be crushed between the
motor and the clamp bracket when the

motor is trimmed or tilted.

WARNING

EWM00250

Leaking fuel is a fire hazard. If there is a
fuel joint on the outboard motor, discon-
nect the fuel line or close the fuel cock if
the engine will be tilted for more than a

few minutes. Otherwise fuel may leak.

NOTICE

ECM00241

●

Before tilting the outboard motor, stop
the engine by following the procedure
on page 51. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

●

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this

could break the handle.

EMU2797A

Procedure for tilting up (manual tilt
models)

1.

Place the remote control lever / gear
shift lever in neutral.

ZMU05533

N

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
59
60
61
62
63
...
»

Содержание F-20









































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20

Бренд: JBL Страницы: 30

Бренд: A and T Labs Страницы: 44

Бренд: Quest Engineering Страницы: 19

Бренд: ifi Страницы: 21

Бренд: QSC Страницы: 8

Бренд: Kawai Страницы: 64

Бренд: Kawai Страницы: 28

Бренд: Kawai Страницы: 28

Бренд: Opus Technologies Страницы: 8

Go Wireless Series

Бренд: Vernier Страницы: 3

Бренд: Alpha Страницы: 4

Бренд: Crown Страницы: 1

Бренд: Carson Страницы: 12

Бренд: Teac Страницы: 4

Бренд: Lanzar Страницы: 13

Бренд: Monacor Страницы: 34

Classic Chorus 212

Бренд: Peavey Страницы: 19

Бренд: MTI Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды