Yamaha F-20 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 104

background image

1

Safety information

EMU33622

Outboard motor safety

Observe these precautions at all times.

EMU36500

Propeller

People can be injured or killed if they come
in contact with the propeller. The propeller
can keep moving even when the motor is in
neutral, and sharp edges of the propeller can
cut even when stationary.

●

Shut off the engine when a person is in the
water near you.

●

Keep people out of reach of the propeller,
even when the engine is off.

EMU33630

Rotating parts

Hands, feet, hair, jewelry, clothing, PFD
straps, etc. can become entangled with inter-
nal rotating parts of the engine, resulting in
serious injury or death.
Keep the top cowling in place whenever pos-
sible. Do not remove or replace the cowling
with the engine running.
Only operate the engine with the cowling re-
moved according to the specific instructions
in the manual. Keep hands, feet, hair, jewel-
ry, clothing, PFD straps, etc. away from any
exposed moving parts.

EMU33640

Hot parts

During and after operation, engine parts are
hot enough to cause burns. Avoid touching
any parts under the top cowling until the en-
gine has cooled.

EMU33650

Electric shock

Do not touch any electrical parts while start-
ing or operating the engine. They can cause
shock or electrocution.

EMU34790

Power tilt

Body parts can be crushed between the mo-

tor and the clamp bracket when the motor is
trimmed or tilted. Keep body parts out of this
area at all times. Be sure no one is in this
area before operating the power tilt mecha-
nism.
The power tilt switches operate even when
the main switch is off. Keep people be away
from the switches whenever working around
the motor.
Never get under the lower unit while it is tilt-
ed, even when the tilt support lever or knob
is locked. Severe injury could occur if the
outboard motor accidentally falls.

EMU33671

Engine shut-off cord (lanyard)

Attach the engine shut-off cord so that the
engine stops if the operator falls overboard
or leaves the helm. This prevents the boat
from running away under power and leaving
people stranded, or running over people or
objects.
Always attach the engine shut-off cord to a
secure place on your clothing or your arm or
leg while operating. Do not remove it to leave
the helm while the boat is moving. Do not at-
tach the cord to clothing that could tear
loose, or route the cord where it could be-
come entangled, preventing it from function-
ing.
Do not route the cord where it is likely to be
accidentally pulled out. If the cord is pulled
during operation, the engine will shut off and
you will lose most steering control. The boat
could slow rapidly, throwing people and ob-
jects forward.

EMU33810

Gasoline

Gasoline and its vapors are highly flam-
mable and explosive.

Always, refuel ac-

cording to the procedure on page 44 to
reduce the risk of fire and explosion.

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
5
6
7
8
9
...
»

Содержание F-20









































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: B&K Страницы: 24

Бренд: NAD Страницы: 12

Бренд: NAD Страницы: 38

Бренд: NAD Страницы: 14

Бренд: NAD Страницы: 5

Бренд: NAD Страницы: 4

AudioControl Director M4800

Бренд: Janus Страницы: 16

Бренд: Vox Страницы: 2

Бренд: Artec Страницы: 2

Бренд: Fender Страницы: 20

Бренд: Signal Страницы: 16

Бренд: Meec tools Страницы: 23

Бренд: Cable Ferret Страницы: 16

Бренд: Randall Страницы: 6

XXRK-630SP4-14SG-ST4

Бренд: J&M Corporation Страницы: 9

Бренд: Vitus Audio Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды