background image

 

Safety information

 

6

 

Crossing

 

When two power driven vessels are crossing
each other’s path close enough to run the
risk of collision, the vessel which has the oth-
er on the starboard (right) side must keep out
of the way of the other. If the other vessel is
on your right, you must keep out of its way;
you are the Give-Way vessel. If the other
vessel is on your port (left) side, remember
that you should maintain course and direc-
tion, provided the other vessel gives you the
right-of-way as it should.

 

Overtaking

 

If you are passing another vessel, you are
the “Give-Way” vessel. This means that the
other vessel is expected to maintain its
course and speed. You must stay out of its
way until you are clear of it. Likewise, if an-
other vessel is passing you, you should
maintain your speed and direction so that the
other vessel can steer itself around you.

 

EMU25531

 

Other special situations

 

There are three other rules you should be
aware of when driving your boat around oth-
er vessels.

 

Narrow channels and bends

 

When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a power-
driven vessel is preparing to go around a
bend that may obstruct the view of other wa-
ter vessels, the operator should sound a pro-
longed blast on the whistle (4 to 6 seconds).
If another vessel is around the bend, it too
should sound the whistle. Even if no reply is
heard, however, the vessel should still pro-
ceed around the bend with caution. If you
navigate such waters with your boat, you will
need to carry a portable air horn, available
from local marine supply stores.

 

Fishing vessel right-of-way

 

All vessels that are fishing with nets, lines or
trawls are considered to be “fishing vessels”
under the International Rules. Vessels with
trolling lines are not considered fishing ves-
sels. Fishing vessels have the right-of-way
regardless of position. Fishing vessels can-
not, however, impede the passage of other
vessels in narrow channels.

 

Sailing vessel right-of-way

 

Sailing vessels should normally be given the
right-of-way. The exceptions to this are:
1.

When the sailing vessel is overtaking
the power-driven vessel, the power-driv-
en vessel has the right-of-way.

2.

Sailing vessels should keep clear of any
fishing vessel.

3.

In a narrow channel, a sailing vessel
should not hamper the safe passage of
a power-driven vessel that can navigate
only in such a channel.

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F-20









































































































Отзывы: