Yamaha F-20 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 104

background image

Specifications and requirements

17

Fire, explosion or sparks could result.

[EWM01820]

EMU36300

Multiple batteries

To connect multiple batteries, such as for
multiple engine configurations or for an ac-
cessory battery, consult your Yamaha dealer
about battery selection and correct wiring.

EMU25730

Without a rectifier or Rectifier
Regulator

NOTICE

ECM01090

A battery cannot be connected to models
that do not have a rectifier or Rectifier

Regulator.

If you wish to use a battery with the models
without a rectifier or Rectifier Regulator, in-
stall an optional Rectifier Regulator.
Using a maintenance-free battery with the
above models can shorten the life of the bat-
tery significantly.
Install an optional Rectifier Regulator or use
accessories rated to withstand 18 volts or
higher with the above models. Consult your
Yamaha dealer for details on installing an
optional Rectifier Regulator.

EMU34191

Propeller selection

Next to selecting an outboard, choosing the
right propeller is one of the most important
purchasing decisions a boater can make.
The type, size, and design of your propeller
have a direct impact on acceleration, top
speed, fuel economy, and even engine life.
Yamaha designs and manufactures propel-
lers for every Yamaha outboard motor and
every application.
Your outboard motor came with a Yamaha
propeller chosen to perform well over a
range of applications, but there may be uses

where a different propeller would be more
appropriate.
Your Yamaha dealer can help you select the
right propeller for your boating needs. Select
a propeller that will allow the engine to reach
the middle or upper half of the operating
range at full throttle with the maximum boat-
load. Generally, chose a larger pitch propel-
ler for a smaller operating load and a smaller
pitch propeller for a heavier load. If you carry
loads that vary widely, chose the propeller
that lets the engine run in the proper range
for your maximum load but remember that
you may need to reduce your throttle setting
to stay within the recommended engine
speed range when carrying lighter loads.
For instructions on propeller removal and in-
stallation, see page 76.

EMU25770

Start-in-gear protection

Yamaha outboard motors or Yamaha-ap-
proved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started only
when it is in neutral. Always select neutral
before starting the engine.

1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)

ZMU04605

-

x

1

2 3

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
21
22
23
24
25
...
»

Содержание F-20









































































































Отзывы:

Нет отзывов

Похожие инструкции для F-20

Бренд: DAD Страницы: 24

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 44

Бренд: JBL Страницы: 23

Бренд: Kawai Страницы: 40

Бренд: Warwick Страницы: 14

Бренд: Party Light & Sound Страницы: 19

Бренд: ORANGE Страницы: 13

Бренд: moon Страницы: 12

HAKIT-RTG Series

Бренд: l-com Страницы: 27

Mini-Pre Vacuum Tube Microphone PreAmp

Бренд: dbx Страницы: 12

Бренд: Inline Страницы: 11

Бренд: rauland Страницы: 16

Бренд: Flintec Страницы: 22

Бренд: SoundMax Страницы: 28

Tweedle Delight

Бренд: Ceriatone Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды