Yamaha 70 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 94

Yamaha 70 Скачать руководство пользователя страница 75

Maintenance

69

the screws firmly.

EMU29312

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

NOTICE

ECM00720

Do not paint anodes, as this would render

them ineffective.

TIP:

Inspect ground leads attached to external
anodes on equipped models. Consult a
Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-
er unit.

EMU29322

Checking battery (for electric start
models)

WARNING

EWM01900

Battery electrolytic fluid is poisonous
and caustic, and batteries generate ex-
plosive hydrogen gas. When working
near the battery:

●

Wear protective eye gear and rubber
gloves.

●

Do not smoke or bring any other source
of ignition near the battery.

Refer to page 14 for detailed safety infor-

mation about batteries.

The procedure for checking the battery var-
ies for different batteries. This procedure
contains typical checks that apply to many
batteries, but you should always refer to the
battery manufacturer’s instructions.

NOTICE

ECM01920

A poorly maintained battery will quickly

deteriorate.

1.

Check the electrolyte level.

2.

Check the battery’s charge. If your boat
is equipped with the digital speedome-
ter, the voltmeter and low battery alert
functions will help you monitor the bat-
tery’s charge. If the battery needs charg-

ZMU01901

ZMU02559

«
...
73
74
75
76
77
...
»

Содержание 70































































































Отзывы:

Нет отзывов