Yamaha 70 Скачать руководство пользователя | Manualshive

Страница: 26 / 94

background image

Components

20

EMU25830

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU26181

Remote control box

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

1. Fuel joint
2. Fuel gauge
3. Fuel tank cap
4. Air vent screw

ZMU03157

1

3

4

2

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine shut-off switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

«
...
24
25
26
27
28
...
»

Содержание 70































































































Отзывы:

Нет отзывов

Похожие инструкции для 70

Бренд: Yamaha Страницы: 87

Бренд: Biostar Страницы: 27

RTKA788152DE0000BU

Бренд: Renesas Страницы: 11

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Texas Instruments Страницы: 18

Бренд: Texas Instruments Страницы: 24

Бренд: Aaeon Страницы: 119

Бренд: ASROCK Страницы: 64

Бренд: Biostar Страницы: 31

Бренд: ECS Страницы: 82

Бренд: CHAINTECH Страницы: 59

Бренд: ECS Страницы: 70

Бренд: IBASE Technology Страницы: 81

Бренд: Gigabyte Страницы: 112

Бренд: Global American Страницы: 132

MIC23031-4YMT EV

Бренд: Micrel Страницы: 8

WAFER - E668EV ATX

Бренд: IEI Technology Страницы: 59

44011-0208-13-2

Бренд: S&T Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды