Yamaha 70 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 94

Yamaha 70 Скачать руководство пользователя страница 71

Maintenance

65

TIP:

Correct idling speed inspection is only possi-
ble if the engine is fully warmed up. If not
warmed up fully, the idle speed will measure
higher than normal. If you have difficulty ver-
ifying the idle speed, or the idle speed re-
quires adjustment, consult a Yamaha dealer
or other qualified mechanic.
2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 13.

EMU29061

Checking water in engine oil tank

A translucent water drain hose is connected
from the bottom of the oil tank to the filler
neck. If water or foreign matter collects in this
hose, consult a Yamaha dealer.

EMU29112

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU32111

Checking propeller

WARNING

EWM01880

You could be seriously injured if the en-
gine accidentally starts when you are
near the propeller.

●

Before inspecting, removing, or install-
ing the propeller, place the shift control
in neutral, turn the main switch to “

”

(off) and remove the key, and remove
the clip from the engine shut-off switch.
Turn off the battery cut-off switch if

your boat has one.

Do not use your hand to hold the propeller
when loosening or tightening the propeller
nut. Put a wood block between the anti-cavi-
tation plate and the propeller to prevent the
propeller from turning.

Checkpoints

1. Drain hose
2. Filler neck side

ZMU03898

2

1

ZMU03841

ZMU01897

«
...
69
70
71
72
73
...
»

Содержание 70































































































Отзывы:

Нет отзывов