Yamaha 70 Скачать руководство пользователя | Manualshive

Страница: 20 / 94

background image

Specifications and requirements

14

Gear oil quantity:

0.610 L (0.645 US qt, 0.537 Imp.qt)

Tightening torque for engine:

Spark plug:

25.0 Nm (2.55 kgf-m, 18.4 ft-lb)

Propeller nut:

35.0 Nm (3.57 kgf-m, 25.8 ft-lb)

EMU33553

Installation requirements

EMU33563

Boat horsepower rating

WARNING

EWM01560

Overpowering a boat can cause severe

instability.

Before installing the outboard motor(s), con-
firm that the total horsepower of your mo-
tor(s) does not exceed the boats maximum
horsepower rating. See the boat’s capacity
plate or contact the manufacturer.

EMU33571

Mounting motor

WARNING

EWM01570

●

Improper mounting of the outboard mo-
tor could result in hazardous condi-
tions such as poor handling, loss of
control, or fire hazards.

●

Because the motor is very heavy, spe-
cial equipment and training is required

to mount it safely.

Your dealer or other person experienced in
proper rigging should mount the motor using
correct equipment and complete rigging in-
structions. For further information, see page
33.

EMU33581

Remote control requirements

WARNING

EWM01580

●

If the engine starts in gear, the boat can

move suddenly and unexpectedly, pos-
sibly causing a collision or throwing
passengers overboard.

●

If the engine ever starts in gear, the
start-in-gear protection device is not
working correctly and you should dis-
continue using the outboard. Contact

your Yamaha dealer.

The remote control unit must be equipped
with a start-in-gear protection device(s). This
device prevents the engine from starting un-
less it is in neutral.

EMU25694

Battery requirements

EMU25713

Specifications of Battery

Use a fully charged battery that meets the
following specifications. The engine cannot
be started if battery voltage is too low.

NOTICE

ECM01061

Do not use a battery that does not meet
the specified capacity. If a battery that
does not meet specifications is used, the
electric system could perform poorly or
be overloaded, causing electric system

damage.

EMU36290

Mounting battery

Mount the battery holder securely in a dry,
well-ventilated, vibration-free location in the

Minimum cold cranking amps (CCA/
SAE):

380.0 A

Minimum marine cranking amps (MCA/
ABYC):

502.0 A

Minimum reserve capacity (RC/SAE):

124 minutes

«
...
18
19
20
21
22
...
»

Содержание 70































































































Отзывы:

Нет отзывов

Похожие инструкции для 70

Бренд: MPS Страницы: 6

Бренд: ECS Страницы: 56

Бренд: Gigabyte Страницы: 40

Бренд: Gigabyte Страницы: 58

cpuModules CME34BT

Бренд: rtd Страницы: 110

Бренд: Gigabyte Страницы: 31

Бренд: Xilinx Страницы: 55

Бренд: Supermicro Страницы: 91

Бренд: Texas Instruments Страницы: 54

Бренд: MSI Страницы: 112

K8N Neo3 MS-7135

Бренд: MSI Страницы: 124

Бренд: Raider Outboards Страницы: 73

Бренд: ON Semiconductor Страницы: 8

Бренд: EPOX Страницы: 64

Бренд: Linear Technology Страницы: 8

FEBFAN6604MR_CH11U65A

Бренд: Fairchild Страницы: 22

Motherboard PR-DLS533

Бренд: Asus Страницы: 142

Бренд: Asus Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды