Yamaha 70 Скачать руководство пользователя

Страница: 74 / 94

Maintenance

TIP:

For disposal of used oil, consult your
Yamaha dealer.
5.

Put the outboard motor in a vertical po-
sition. Using a flexible or pressurized fill-
ing device, inject the gear oil into the
gear oil drain screw hole.

Put a new gasket on the oil level plug.
When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

Put a new gasket on the gear oil drain
screw. Insert and tighten the gear oil
drain screw.

EMU29302

Cleaning fuel tank

WARNING

EWM00920

Gasoline is highly flammable, and its va-

pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Keep away from sparks, cigarettes,
flames, or other sources of ignition
when cleaning the fuel tank.

●

Remove the fuel tank from the boat be-
fore cleaning it. Work only outdoors in
an area with good ventilation.

●

Wipe up any spilled fuel immediately.

●

Reassemble the fuel tank carefully. Im-
proper assembly can result in a fuel
leak, which could result in a fire or ex-
plosion hazard.

●

Dispose of old gasoline according to lo-

cal regulations.

Empty the fuel tank into an approved
container.

Pour a small amount of suitable solvent
into the tank. Install the cap and shake
the tank. Drain the solvent completely.

Remove the screws holding the fuel joint
assembly. Pull the assembly out of the
tank.

Clean the filter (located on the end of the
suction pipe) in a suitable cleaning sol-
vent. Allow the filter to dry.

Replace the gasket with a new one. Re-
install the fuel joint assembly and tighten

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

0.610 L (0.645 US qt, 0.537 Imp.qt)

Tightening torque:

9 Nm (0.9 kgf-m, 6.6 ft-lb)

Tightening torque:

9 Nm (0.9 kgf-m, 6.6 ft-lb)

ZMU03132

ZMU02066

Содержание 70































































































Результаты поиска

Содержание 70

Отзывы:

Похожие инструкции для 70

Бренды по названию

Популярные бренды

Yamaha 70, Руководство пользователя

Результаты поиска

Содержание 70

Отзывы:

Похожие инструкции для 70

Бренды по названию

Популярные бренды