Yamaha 70 Скачать руководство пользователя страница 35

Страница: 35 / 94

Instruments and indicators

EMU26551

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
alert indicator will start to blink. For further in-
formation, see page 31.

NOTICE

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26583

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
31.

NOTICE

ECM00052

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-

gine damage will occur.

EMU26471

Analog tachometer

This gauge shows the engine speed and has
the following functions.

EMU26541

Oil level indicators (three indicators)

The indicators on the gauge show the status
of the oil level. For details on how to read the
indicators, see page 42.

NOTICE

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

1. Oil level indicator

ZMU01867

1. Overheat-alert indicator

1. Tachometer
2. Oil level indicator

ZMU01868

ZMU04577

Содержание 70































































































Результаты поиска

Содержание 70

Отзывы:

Похожие инструкции для 70

Бренды по названию

Популярные бренды

Yamaha 70, Руководство пользователя

Результаты поиска

Содержание 70

Отзывы:

Похожие инструкции для 70

Бренды по названию

Популярные бренды