Yakima LockNLoad Track Mounting Kit Скачать руководство пользователя страница 9

Страница: 9 / 14

28-13-010_8000316_Rev4

9/14

BAR PLACEMENT

Carefully place front Bar assembly over Nut Plates, ensuring spacing is correct
as shown in the previous Step.

Take care not to damage vehicle.

Position Legs

along Bar until

both legs are securely positioned on Nut Plates within Track.

BAR LOCATION

IMPORTANT: Before beginning Bar installation, identify where along the Track
you want the Front and Rear Bars fitted.
We recommend a minimum of 700 mm between Bars.

≥

700 mm

SECURE BAR ASSEMBLY TO TRACKS

From the LockNLoad Track Kit, insert
1 x M6 Hex Screw through the two
outer holes on Legs into Nut Plate as
shown.

Loosely secure Screws using a 5 mm
ball end Allen Key.

ADJUST BAR OVER HANG

Use a Tape Measure to ensure even Bar overhang on each side, re-adjust if
required by sliding bar along legs.

NOTE -

Bars require individual adjustment due to tapered

roof. Bars must be installed perpendicular to Tracks.

Содержание LockNLoad Track Mounting Kit















Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды

Yakima LockNLoad Track Mounting Kit, Руководство пользователя

Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды