Yakima LockNLoad Track Mounting Kit Скачать руководство пользователя страница 11

Страница: 11 / 14

28-13-010_8000316_Rev4

11/14

SECURE END CAPS TO BARS

Insert the End Caps as shown. A Rubber
Mallet can be used to assist installation.

Secure using Plastite Screw
(from LockNLoad Bar Kit).
Tighten using a #2 Phillips
Head Screwdriver.

BAR SLOT COVERS (OUTSIDE LEG)

Measure the Bar channel outside of
the Legs and subtract 20 mm from
this measurement.

Using the remaining pieces of
Slot Cover from the previous
Step, cut to this length and
press into the underside channel
of each Bar end as shown.

-20 mm

BAR SLOT COVERS (INSIDE LEG)

From the LockNLoad Bar Kit, cut Bar Slot
Covers as per measurements recorded
in the previous Step and press into the
underside channel of Bar ends as shown.

NOTE -

Bar Slot Covers to be

inserted with flat side visible

Содержание LockNLoad Track Mounting Kit















Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды

Yakima LockNLoad Track Mounting Kit, Руководство пользователя

Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды