Yakima LockNLoad Track Mounting Kit Скачать руководство пользователя страница 10

Страница: 10 / 14

28-13-010_8000316_Rev4

10/14

CHECK BAR SLOT MEASUREMENTS

Place Bars on flat surface with legs facing upwards, as
shown. Take appropriate measures to avoid scratching
the product and surface.

Identify slot on each Bar end. Using a Tape Measure,
record Leg to underside slot distance of each bar in the
table (right). Ensure measurement is taken from the
centre of the Legs as shown.

X = X

Y = Y

BAR SLOT

MEASUREMENTS

Bar 1 (X)

______mm x2

Bar 2 (Y)

______mm x2

The ends of each bar should be the same
measurement respectively, if not, loosen M8
Set Screws and repeat Steps 23-28.

SECURE LEGS TO BARS

Tighten all M8 Set
Screws to 9 Nm using
a 13 mm Spanner.

REPEAT AND REMOVE

Repeat Steps 23 - 26 for
remaining bar assembly.

Carefully remove all Bar and
Leg assemblies from vehicle.

Содержание LockNLoad Track Mounting Kit















Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды

Yakima LockNLoad Track Mounting Kit, Руководство пользователя

Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды