Yakima LockNLoad Track Mounting Kit Скачать руководство пользователя страница 4

Страница: 4 / 14

28-13-010_8000316_Rev4

4/14

ALIGN TRACK

Place Track into roof channel, ensuring there is a 2 mm spacing
from end of trim to Track both front and rear as shown.

Apply lengths of Masking Tape along window and door seals.
This prevents drill swarf from getting caught.

APPLY MASKING TAPE

2 mm

SPOT DRILL RIVET HOLES

With the help of an assistant, hold track down firmly in roof channel. Using
the supplied 4.9 mm Drill Bit, start spot drilling each rivet hole in the Track

from the rear of the vehicle working consecutively frontward.

Ensure the

Track does not move during this process by maintaining downward pressure on
the Track.

Once complete, remove Track taking care not to scratch vehicle.

Drill frontward

Vehicle Front

Vehicle Rear

Содержание LockNLoad Track Mounting Kit















Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды

Yakima LockNLoad Track Mounting Kit, Руководство пользователя

Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды