Yakima LockNLoad Track Mounting Kit Скачать руководство пользователя страница 12

Страница: 12 / 14

28-13-010_8000316_Rev4

12/14

Position front and rear Bars along Tracks as required, ensuring there is a minimum
distance of 700 mm between each Bar.

Measure from the centre of each Leg as shown.

M6 HEX SCREW ASSEMBLY

From the LockNLoad Track
Kit, assemble 1 x M6 Spring
Washer and 1 x M6 Washer
onto each M6 Hex Screw.

Insert through the outer
holes on Legs into Nut
Plates as shown.

BAR FITMENT

Slide Nut Plates in Track into position for Bar placement (it doesn’t have
to be exact). Place Bar assembly onto Tracks, carefully locating the four
central raised notches on base of Legs into the cut outs on Nut Plates as
shown.

Take care not to damage vehicle.

Repeat for remaining Bar.

≥

700 mm

Содержание LockNLoad Track Mounting Kit















Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды

Yakima LockNLoad Track Mounting Kit, Руководство пользователя

Результаты поиска

Содержание LockNLoad Track Mounting Kit

Отзывы:

Похожие инструкции для LockNLoad Track Mounting Kit

Бренды по названию

Популярные бренды