Yaesu FTM-200DR Скачать руководство пользователя страница 32

Страница: 32 / 67

• Make sure to turn the transceiver OFF before connecting any cables.

• When using the SCU-20 PC connection cable, install the designated driver on the

computer. Download the driver and installation manual from the Yaesu website.

Transmitting GPS location information

The GPS position data (latitude/longitude) of this station can be output from the serial

DATA jack on the rear of the transceiver.
1. Press and hold the [

MENU

] key



[

66 COM PORT

]



Press the

DIAL

knob

2. Rotate the

DIAL

knob to select [

SPEED

] then press the

DIAL

knob.

3. Rotate the

DIAL

knob to select the desired communication speed then press the

DIAL

knob.

The setting changes in the following order:

4800bps



9600bps



19200bps



38400bps



57600bps

Factory default value: 9600bps

4. Rotate the

DIAL

knob to select [

OUTPUT

] then press the

DIAL

knob.

5. Rotate the

DIAL

knob to select “

GPS OUT

” then press the

DIAL

knob.

The setting changes in the following order:

OFF



GPS OUT



PACKET



WAYPOINT

Factory default value: OFF

6. Press any key (except Power Switch) or

PTT

switch to finish the setting and return to

the original screen.

Transmits the location information data. The location data is output to the computer at

about one second intervals.

An operating software using NMEA-0183 standard GGA and RMC sentence is required to

use the position information.

Updating the transceiver firmware

When updated firmware is available, the transceiver can be updated by connecting it to a

personal computer. Download the latest version of the firmware and the firmware installa-

tion manual from the YAESU website.

Содержание FTM-200DR




































































Результаты поиска

Содержание FTM-200DR

Отзывы:

Похожие инструкции для FTM-200DR

Бренды по названию

Популярные бренды

Yaesu FTM-200DR, Руководство для продвинутых пользователей

Результаты поиска

Содержание FTM-200DR

Отзывы:

Похожие инструкции для FTM-200DR

Бренды по названию

Популярные бренды