Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT..., Руководство по эксплуатации

Страница: 41 / 180

Page 39 FT
DX
9000MP O
PERATION
M
ANUAL
Main (VFO-A) Band TX/RX Indicators
These combination lamp-buttons select and indicate
the transmit/receive status of the Main band (VFO-
A). When the green “RX” lamp is lit, the receiving
frequency is under control of the main knob and dis-
play (either VFO-A or a recalled memory channel).
When the red “TX” lamp is lit, the transmitting fre-
quency is under control of the main knob and display.
Thus, for “normal” (non-split) operation, both the red
and green lamps associated with the main tuning knob
will be illuminated.
Main (VFO-A) Frequency Display
This is the Main band (VFO-A) frequency display.
A A A A A
D D D D DVICE VICE VICE VICE VICE
: When setting the CTCSS frequency for En-
coding or Tone Squelch operation, the tone
information will appear in this area during
setup.
Sub Band (VFO-B) TX/RX Indicators
These combination lamp-buttons select and indicate
the transmit/receive status of the Sub band (VFO-B).
Sub Band (VFO-B) Frequency Display
This is the Sub band (VFO-B) frequency display.
A A A A A
D D
D D DVICE
VICE
VICE VICE VICE
ˆ When activating the CW Spot Tone, the current
tone frequency will appear in this area.
ˆ When turning the [ PITCH
], [
SPEED
], [
CON-
TOUR
], [
NOTCH
], [
DNR
], [
CW DELAY
],
[
VOX DELAY
], [
RF PWR
], [
MIC GAIN
], or
[
PROC
] knob, each frequency or value will ap-
pear in this area for 3 seconds.
If the knob is turned too slowly, the frequency
display may not show the value. This is to pre-
vent undesired display of the functions caused
by noise or slight vibration of the controls; how-
ever, the actual value will be changed even if
not displayed.
You can observe the fine adjustment for a few
seconds while the display is active.
While adjusting functions, the display may oc-
casionally skip one of the numbers in the se-
quence; this is due to “rounding” of the encoder
steps in the ADC converter. Set the values to your
preference, they are unique to your radio and
may not directly correspond to other units. .
ˆ The Tone Encoder/Decoder frequency is indicated
during the FM mode setup process.
Multi-Panel
This field within the frequency display area provides
several indications, depending on the frequency con-
trol mode in use:
CLAR (Clarifier)
This window displays the Clarifier frequency offset
from the Main band (VFO-A) frequency. The Clari-
fier is engaged when the CLAR LED is illuminated.
MR (Memory Recall)
When the [
MCH/GRP ] switch (#
) is pushed, the
currently-selected Memory channel or Memory Group
number will be displayed in this window.
MT (Memory Tune)
If you rotate the [ Main Tuning Dial
] knob (“
) (or
change the mode) during memory operation, the trans-
ceiver will change into the “Memory tune” mode to
indicate that the memory contents have been tempo-
rarily changed; “
” lights up to confirm this change.
Repeater Shift Data
During FM operation, the Repeater Shift will be indi-
cated in this window.
A Negative frequency shift will be indicated by “-”
while a Positive frequency shift will be indicated by
“+” in the window. During Simplex operation (no
shift), “S” will be displayed.
FFFFF
REQ REQ
REQ REQ
REQUENCY UENCY
UENCY UENCY
UENCY
D D D D D
ISPLA ISPLA
ISPLA ISPLA
ISPLAYYYYY