Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT..., Руководство по эксплуатации

Страница: 143 / 180

Page 141 FT
DX
9000MP O
PERATION
M
ANUAL
AAAAA
BOUT BOUT
BOUT BOUT BOUT
THE THE
THE THE THE
TTTTT
RANSVER RANSVER
RANSVER RANSVER RANSVERTER
TER
TER TER TER
O O O O O
UTPUT UTPUT
UTPUT UTPUT UTPUT
TTTTT
ERMIN ERMIN
ERMIN ERMIN ERMINAL
ALAL
AL AL
You may connect an after-market transverter to the rear panel’s TRV (Transverter) jack. The output, at 28 MHz, is approxi-
mately –20 dBm (0.01 mW) at 50 Ohms.
S
ETUP
1. Press the [ MNU
] key to enter the Menu mode (the
LCD will change to Menu display).
2. Rotate the [ MAIN Tuning Dial
] knob to choose Menu
item “ TUNING 145 MY BAND ”.
3. Rotate the [
CLAR/VFO-B
] knob to find the Menu
parameter “TRV OFF” (this is the factory default set-
ting).
4. Press the [
ENT
] key to change the parameter to “TRV
ON” (this will add this condition to your “My Band”
list; see page 56).
5. Press and hold in the [
MNU
] key for at least two sec-
onds to save the new setting and exit to normal opera-
tion.
O
PERATION
1. Set up the frequency offset for transverter use, as de-
scribed previously.
2. Rotate the [ MAIN Tuning Dial
] knob to set the de-
sired operating frequency. Operation is basically un-
changed from normal transceiver operation.
A A
A A
A
D D D D DVICE VICE VICE VICE VICE
When the “TRV” mode is turned on, power output
will not be allowed to pass to the
[ ANT1 ]
~
[ ANT4 ]
main antenna jacks. So one of these may be con-
nected to your transverter’s “RX” jack. Just be cer-
tain to disconnect the transverter when returning to
HF operation, as the selected Antenna jack will now
be capable of passing RF power.
1. Connect the 144 MHz transverter to the transceiver.
2. Use the Menu mode to confirm that Menu item
“ GENERAL 042 TRV OFFSET ” is set to “44”
(the factory default setting).
3. Press the [ BAND/MHz
] key momentarily, then ro-
tate the [ CLAR/VFO-B
] knob so as to select
“44.000000” on the display.
4. Press and hold in the [ MNU
] key for at least two
seconds to save the new setting and exit.
The “100 MHz” digit of the frequency is not displayed,
so when you are operating on 2 meters and see “45
MHz” on the frequency readout, this indicates “145
MHz” instead.
A A A A A
D D D D DVICE VICE VICE VICE VICE
:
With the setup described above, tuning the operating
range 28-29 MHz will correspond to an actual operat-
ing frequency of 144-145 MHz, with “44-45” being
displayed on the front panel of the transceiver.
Setting the Transverter Frequency Offset
You may set up the frequency display so that it shows the actual band on which your transverter is operating (instead
of the “IF” used by the transverter, which is the 28 MHz band on your
FT
DX
9000MP ).
E E
E E E
XAMPLE XAMPLE XAMPLE XAMPLE XAMPLE
: Setting Up the
FT
DX
9000MP
Display for Use with a 144 MHz Transverter
TX GND
Transceiver V/U ANT
RF IN
V
/U
H
F
A
n
te
n
n
a
同軸ケーブル（ Ω）
50
TRV Jack Pin 2 (TX GND) of BAND DATA 1Jack or
Pin 2 (TX GND) of BAND DATA 2 Jack
Coaxial Cable (50 Ohm)