Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT..., Руководство по эксплуатации

Страница: 123 / 180

Page 121 FT
DX
9000MP O
PERATION
M
ANUAL
FM M FM M
FM M FM M
FM M
ODE ODE
ODE ODE ODE
O O O O O
PERA PERA
PERA PERA PERATION
TION
TION TION TION
CTCSS Tone Frequency (Hz)
67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4
88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9
114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2
151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8
177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5
203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8
250.3 254.1
Repeater Shift Direction
S : Simplex
-- : Minus Shift
+ : Plus Shift
CTCSS Tone Frequency
CTCSS Operation
tn : Tone Encoder
tS : Tone Squelch
oFF : OFF
R
EPEATER
O
PERATION
The FT
DX
9000MP may be utilized on 29 MHz and 50 MHz repeaters.
1. Rotate the [ MAIN Tuning Dial
] knob to the output
frequency (downlink) from the repeater.
2. If CTCSS Tone operation is desired/needed, press and
hold in the [ FM
] Mode key for two seconds to engage
the CTCSS mode.
3. Rotate the [ MAIN Tuning Dial
] knob to select the
desired CTCSS mode. If you just need to send the
uplink encoding tone, select “
tn .” For encode/decode
operation, choose “ ts ” instead.
The available choices are
“OFF” “tn” “ts” “OFF.”
4. Rotate the [ CLAR/VFO-B
] knob to select the desired
CTCSS Tone to be used. A total of 50 standard CTCSS
tones are provided (see the CTCSS Tone Chart).
5. Press the [ FM
] Mode key to selec the desired repeater
shift direction. The selections are:
“S” “+” “
−
” “S”
where “S” represents “Simplex” operation (not used
on a repeater).
6. Press and hold in the [ FM
] Mode key for two seconds
to exit from the repeater setup mode.
7. Close the microphone’s PTT switch (or press the
[
MOX
] switch to begin transmission. You will observe
that the frequency has shiftd to correspond to the pro-
gramming you set up in the previous steps. Speak into
the microphone in a normal voice level, and release
the PTT or [
MOX
] switch to return to the receive
mode.
A A A A A
D D D D DVICE VICE VICE VICE VICE
The conventional repeater shift used on 29 MHz is
100 kHz, while on the 50 MHz band the shift may
vary between 500 kHz and 1.7 kHz (or more). To
program the proper repeater shift, use Menu items
“
MODE-FM 068 RPT SHIFT (28 MHz) ” and
“ MODE-FM 069 RPT SHIFT (50 MHz) ”, as ap-
propriate.
[Main Tuning Dial] Knob
VDD TEMP SWR BIAS
[MODE] Switch
[CLAR/VFO-B] Knob
[MOX] Switch