manualshive.com logo in svg

XYZ Machine Tools ProTURN SLX 1630, Инструкция по безопасности, установке, обслуживанию, эксплуатации и списку запасных частей

Поделиться
Скачать
XYZ Machine Tools ProTURN SLX 1630 Скачать руководство пользователя страница 52

48 

XYZ Machine Tools 

ProTURN SLX 1630 ProtoTRAK SLX CNC Safety, Installation, Service & Parts List Manual 

 

ability to save the configuration file and the machine will need to be re-setup when 

the computer or hard drive is replaced. 

Note: All machines will have a copy of the configuration file in the back of the electric’s 
cabinet. 

4.8.1.5    CODE 313: Display Configuration File 

This code displays the configuration file.  This file contains pertinent information 

about the machine.  The file will look similar to the following.  If the file becomes 

corrupt you can load default values by pressing the F4 softkey. 
Product = 1440S/1745S (displays machine ID key) 

Motor encoder calibration constants 

610.0712 

1143.8921 

 (These numbers above are typical numbers for the calibration constants) 

Arc accuracy – 0.13 

Code 128 

X=0.13  

Z=0.04 

Code 12 (+) 

X=000005 

 

Z=000006 

             (

-

) 

X=000005 

 

Z=000006 

Code 100 (+)  X=352.7 

 

Z=325.2 

               (

-

)  X=350.1 

 

Z=333.1 

4.8.1.6    CODE 316: Update Master Software 

Load upgrade disk in floppy drive and press this service code.  New software will 

automatically download and control will reboot.  Please perform alignment routine 

afterwards. 

4.8.1.7    CODE 317: Update Slave Software 

Load upgrade disk in floppy drive and press this service code.  New software will 

automatically download and control will reboot.  Please perform alignment routine 

afterwards.

 

4.8.1.8   CODE 318: Activate Converters or Options 

See programming and operating manual. 

4.8.2   

Machine Set-up Codes 

The following codes are used primarily when setting up a new machine.  To get to 

any of these codes go to Service Codes, press “B” and press the code you wish to 

view. 

4.8.2.1    CODE 12:  Feed Forward Constant 

The Code 12 procedure helps the control “learn” the friction characteristics of the 

machine by sending a graduated series of motor signals and observing the results.  

The process takes less than 30 seconds to run.  It is both a diagnostic routine that 

displays values, and a routine that sets the parameters of the control for the 

particular machine. 
 
The Code 12 is used for diagnosing and resolving: 

 

Problems with machine motion. 

 

Machined parts come out bad – especially poor finish. 

Note:  Code 12 routine will set the parameters for the particular machine and its particular 
situation.  If the machine changes its friction characteristic, the Feed Forward Constant 
should change too, or the system will not servo properly.  Whenever gibs are adjusted or a 
heavy workpiece has been added to the table, you should run a Code 12.  When the heavy 
workpiece is removed, Code 12 should be run again. 

Содержание ProTURN SLX 1630












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды