XYZ Machine Tools ProTURN SLX 1630 Скачать руководство пользователя страница 30

Страница: 30 / 107

XYZ Machine Tools

ProTURN SLX 1630 ProtoTRAK SLX CNC Safety, Installation, Service & Parts List Manual

3.3.4 Fault X or Z

The program run or jogging operation is interrupted with a Fault Message on the
display.
Do the following Service Codes and procedures:



Code 33

Software Identification. This is needed if you call Customer Service.



Code 12

Feed Forward Constant.



Code 100

Axis open loop test.

Used to check the maximum feedrate of an axis

and if the encoders are counting.

Possible Cause

Check This

Servo cables at pendant switched around.

Make sure during an installation the X and Z servo
cables at the pendant are in the correct ports.

X-axis Gibs are adjusted extremely tight

Check the adjustment of the X-axis Gibs using the X

Gib adjustment procedures. See X-axis Gib
Adjustments Section 5.2.1.

Excessive friction in the slideways

See Machine Tool & Setup Section 4.1.

Binding or looseness in the Drive Train

See Mechanical Drive Train (X, Z) Section 4.2.

Incoming electrical power

Incoming voltage. See Electrical Section 2.10.

Servo Drive failure

See Servo Driver - Section 4.5.

Motor failure

See

Motor diagnostics, Section 4.4.

Computer/Pendant failure

See

Computer/Pendant diagnostics, Section 4.3.

3.3.5 Problems Reading the Floppy Disk; Programs Not Saved

Properly

The floppy drive will not read or write programs from a disk.

Possible Cause

Check This

Improper Boot-up

Shut down the system and wait 10 seconds before
rebooting.

Floppy Disk failure

The Floppy Disk may be bad. See if the Floppy Disk

can be read by a Personal Computer. Does the green
light on the floppy drive come on when you access the

disk? If so, power is getting to the floppy drive. If

not check connections of floppy drive inside the

computer module. See Computer/Pendant Section 4.3

for more information.

Floppy Disk full

Put the Floppy Disk into a Personal Computer to see

how many bytes remain.

3.3.6 System Will Not Turn On

Nothing happens when the switch is turned on.

Possible Cause

Check This

110 V line is not plugged in

Check incoming 110 V power source to electrical cabinet

Pendant On/Off switch is Off.

Check the Pendant On/Off switch

Fuse blown in pendant or electrical

cabinet

Remove fuses and check continuity.

Transformer output

Check 110 V Transformer output

Computer/Pendant has failed

See Computer/Pendant

diagnostics Section 4.3.

3.3.7 System Will Not Boot-Up

The system does not boot-up when the switch is turned on.

Содержание ProTURN SLX 1630












































































































Результаты поиска

Содержание ProTURN SLX 1630

Отзывы:

Бренды по названию

Популярные бренды

XYZ Machine Tools ProTURN SLX 1630, Инструкция по безопасности, установке, обслуживанию, эксплуатации и списку запасных частей

Результаты поиска

Содержание ProTURN SLX 1630

Отзывы:

Бренды по названию

Популярные бренды