manualshive.com logo in svg

XYZ Machine Tools ProTURN SLX 1630, Инструкция по безопасности, установке, обслуживанию, эксплуатации и списку запасных частей

Поделиться
Скачать
XYZ Machine Tools ProTURN SLX 1630 Скачать руководство пользователя страница 35

31 

XYZ Machine Tools 

ProTURN SLX 1630 ProtoTRAK SLX CNC Safety, Installation, Service & Parts List Manual 

 

3.5.2  Spindle Motor Hums or Will Not Run 

The spindle motor makes a constant humming noise during operation or will not turn 
on. 

 

Possible Cause 

Check This 

Wrong voltage 

 

Check the 415V voltage to the machine 

Poor wiring connections 

Check all the wiring connections to the electric’s box. 

Defective cable connections 

Check all cable connections 

Spindle Motor is bad 

Check the resistance of the Spindle Motor windings on the Spindle 

Motor between L1 & L2, L2 & L3, and L1 & L3, using an Ohmmeter. 
The resistance should range from ".7 to 1.8 Ohm". If the Ohmmeter 

reads "0 Ohms" or "OL", then replace Spindle Motor. Next, check the 

resistance between L1 & Ground, L2 & Ground, and L3 & Ground, 

using an Ohmmeter. The resistance should read "OL". If not then 

replace Spindle Motor. 

3.5.3  Spindle Runs Backwards 

The spindle motor runs in the opposite direction. 

 

Possible Cause 

Check This 

3-Phase wires backwards 

Need to switch any 2 of the 3 wires either coming out of the 

Spindle Drive (T1, T2, and T3) or going into the Spindle Motor (U, 

V, and W).  Caution: Be sure to shut off all power to the machine 
before attempting to switch any wires. 

3.5.4  Excess Gearbox Noise

 

Gearbox noise is louder than normal.  Run the lathe at the gear where the noise is 

most noticeable.  Remove the gearbox lid and try to isolate where the noise is 

coming from. 

 

Possible Cause 

Check This 

Insufficient amount of oil in headstock  

Check site glass to make sure oil is at sufficient level. 

Spindle bearing not being lubricated 

properly, worn bearing 

Remove top lid and check to make sure oil is 

overflowing freely to the spindle bearings. 

Spindle preload loose 

Tighten spindle preload on bearing.  The spindle 

preload should be approximately 1.1 – 1.7 N-m. 

3.5.5  Headstock is Leaking Oil 

A Form-A-Gasket sealant should be use to seal any leaking areas.  Make sure the 

sealant fills the leaking area thoroughly.  Sealant must cure for 24 hours for best 
results. 

3.5.5.1  

Leaking Oil from Rear of Gearbox 

Possible Cause 

Check This 

Leaking from behind belt drive pulley 

Replace shaft seal - o-rings or gaskets. 

Oil leaking from behind the spindle 

encoder. 

Remove spindle encoder and pinion shaft cover. 

Check the seal. 

Oil leaking from the rear bearing 

assembly. 

Make sure the spindle shaft cover is mounted 

correctly, if so remove the cover and check the o-ring. 

Содержание ProTURN SLX 1630












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды