Xyplex Network 9000 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 117

background image

Chassis Management Displays

Field

Means

Suspended

The processor module failed to obtain the software load
image because the information in control storage was
invalid or corrupt. To correct this condition, you can change
the information in the initialization records with the
DEFINE CHASSIS SLOT commands, described in Chapter
4.

Run

The processor module is not operational because it has been

Inhibited

suspended, or "held, " either because a user pushed the reset
button on the front panel once, or a user entered the RESET
CHASSIS HOLD command for this slot.

Diagnostics The processor module is running diagnostic programs.

Failed

The processor module was running diagnostics programs,
and these programs failed. If this status appears, contact
your Xyplex representative for more information.

Not

The Single Chip Microcontroller on the module responded

Responding to the request for status, but the operational software did not.

When this status appears, other fields in the display,
including Installed Memory, Link Mappings, and Uptime
do not have status. If the module in the slot returns the status
Not Responding, wait 30 seconds and enter the Slot Status
command for the module in this slot again. If the module
still returns the status Not Responding, contact your Xyplex
representative.

Processor
Module

The model number and revision number of the processor module in this
slot. This display shows a model 410 bridge. If no processor module
exists in this slot, then N/A (not applicable) appears in this field.

The type and revision number of the I/O module in this slot. This display
shows a four port LAN bridge/router, the BR/412. If no I/O module exists
in this slot, then N/A (not applicable) appears in this field.

I/O Module

The amount of memory installed on the processor module.

Installed
Memory

The Ethernet address of the module or module set.

802.x Address

The Internet address of the module or module set.

IP Address

The version of the firmware running on this processor module.

Firmware
Version

The serial number of the processor module.

Proc Mod.
Serial #

94

0020

«
...
89
90
91
92
93
...
»

Содержание Network 9000






















































































































Отзывы:

Нет отзывов

Похожие инструкции для Network 9000

Univerge SV8100

Бренд: NEC Страницы: 78

Univerge SV8100

Бренд: NEC Страницы: 186

Univerge SV8100

Бренд: NEC Страницы: 150

Univerge SV8100

Бренд: NEC Страницы: 52

digitalSTROM-Server

Бренд: aizo Страницы: 2

UniServer R4900 G3

Бренд: H3C Страницы: 24

OmniStor 4900F Series

Бренд: Rackable Systems Страницы: 196

Бренд: BlueNet Video Страницы: 38

A+ AS -2114GT-DNR

Бренд: Supermicro Страницы: 126

Бренд: Sun Microsystems Страницы: 121

VIP Media Server Pro

Бренд: Chauvet Страницы: 20

Бренд: Cisco Страницы: 2

Бренд: myTEM Страницы: 2

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 84

Бренд: QNAP Страницы: 39

Бренд: F5 Страницы: 56

OfficeBasic USB Wireless G

Бренд: Axis Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды