Xylem Flygt 2190 Скачать руководство пользователя страница 60

Страница: 60 / 72

Cause

Remedy

One or more of the valves are set in

the wrong positions.

• Reset the valves that are set in the wrong position.
• Replace the valves, if necessary.
• Check that all valves are correctly installed according to media flow.
• Check that all valves open correctly.

The impeller is difficult to rotate by

hand.

• Clean the impeller.
• Clean out the sump.
• Check that the impeller is properly trimmed.

The pipes are obstructed.

To ensure a free flow, clean out the pipes.

The pipes and joints leak.

Find the leaks and seal them.

There are signs of wear on the

impeller, pump, and casing.

Replace the worn parts.

The liquid level is too low.

• Check that the level sensor is set correctly.
• Depending on the installation type, add a means for priming the pump,

such as a foot valve.

If the problem persists, contact the local sales and service representative. Always state the
serial number of your product, see

Product Description

(page 10).

7 Troubleshooting

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

Содержание Flygt 2190









































































Результаты поиска

Содержание Flygt 2190

Отзывы:

Похожие инструкции для Flygt 2190

Бренды по названию

Популярные бренды

Xylem Flygt 2190, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Flygt 2190

Отзывы:

Похожие инструкции для Flygt 2190

Бренды по названию

Популярные бренды