manualshive.com logo in svg

Xylem Flygt 2190, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2190 Скачать руководство пользователя страница 22

d) Twist all power core screens together to create a ground (earth) core and fit a

cable terminal to the end.

e) Check that the ground (earth) core is at least 10% longer than the phase cores in

the cabinet.

5. How is the connection to ground (earth) made?

• Screw: Fit cable terminals to the ground (earth) core and the power cores.
• Terminal block: Leave the core ends as they are.

6. Prepare the main leads:

a) Remove the aluminum foil around each power core.
b) Peel the insulation from each power core.

4.2.2  Connect the motor cable to the pump: Version code 2190.010, 2201.012/020/320

NOTICE:

Leakage into the electrical parts can cause damaged equipment or a blown fuse. Keep
the end of the motor cable dry at all times.

1

2

WS009000A

Part

Description

1

Screws

2

Entrance flange

Figure 6: Cable entry for version code 2190.010 HT and 2201.012 HT

2

1

1

WS009001A

Part

Description

1

Screws

4  Installation

20

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

Содержание Flygt 2190









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды