manualshive.com logo in svg

Xylem Flygt 2190, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2190 Скачать руководство пользователя страница 13

Pressure class

LT

Low head

MT

Medium head

HT

High head

SH

Super head

Impeller type

B

Wear resistant

Poly-Life

Version code 2190.010/2201.012/2201.020/2201.320: The pump is available with Poly-
Life

®

 polyurethane wear parts for extra resistance.

3.3  Monitoring equipment

The following applies to the monitoring equipment of the pump:

• The stator incorporates thermal contacts connected in series that activate the alarm at

overtemperature.

•

• Version code 2190.010: The thermal contacts open at 140°C (284°F) and close at

105°C (221°F).

• Version code 2201.012/2201.020/2201.320: The thermal contacts open at 125°C

(257°F) and close at 70°C (160°F).

• Version code 590/690/691: The thermal contacts open at 110°C (230°F) and close

at 70°C (160°F).

3.4  The data plate

The data plate is a metal label that is located on the main body of the products. The data
plate lists key product specifications. Specially approved products also have an approval
plate.

2

13

12

14

22

21
20

17 18

19

16

15

9

10

11

8

7

6

5

4

3

1

23

24

WS006257A

1.

Curve code or Propeller code

2.

Serial number

3.

Product number

4.

Country of origin

5.

Additional information

6.

Phase; type of current; frequency

7.

Rated voltage

8.

Thermal protection

9.

Thermal class

10. Rated shaft power

11. International standard

12. Degree of protection

13. Rated current

14. Rated speed

15. Maximum submergence

16. Direction of rotation: L=left, R=right

17. Duty class

3  Product Description

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

11

Содержание Flygt 2190









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды