manualshive.com logo in svg

Xylem Flygt 2190, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2190 Скачать руководство пользователя страница 17

4  Installation

4.1  Install the pump

Before starting work, make sure that the safety instructions in the chapter 

Introduction and

Safety

 (page 3) have been read and understood.

DANGER: Electrical Hazard

Before starting work on the unit, make sure that the unit and the control panel are isolated
from the power supply and cannot be energized. This applies to the control circuit as well.

DANGER: Inhalation Hazard

Before entering the work area, make sure that the atmosphere contains sufficient oxygen
and no toxic gases.

Hazardous atmospheres

DANGER: Explosion/Fire Hazard

Special rules apply to installations in explosive or flammable atmospheres. Do not install
the product or any auxiliary equipment in an explosive zone unless it is rated explosion-
proof or intrinsically-safe. If the product is EN/ATEX-, MSHA- or FM-approved, then see
the specific EX information in the Safety chapter before taking any further actions.

WARNING: Explosion/Fire Hazard

Do not install CSA-approved products in locations that are classified as hazardous in the
National Electric Code(TM), ANSI/NFPA 70-2005.

Authority regulation

Vent the tank of a sewage station in accordance with local plumbing codes.

Sedimentation prevention

In order to avoid sedimentation when the pumped liquid contains solid particles, the
velocity of the liquid in the discharge line must exceed a certain value. Choose applicable
minimum velocity from the table, and choose proper dimension of the discharge line
accordingly.

Mixture

Minimum velocity, meter per second (feet per second)

Water + coarse gravel

4 (13)

Water + gravel

3.5 (11)

Water + sand, particle size <0.6 mm (0.024 in)

2.5 (8.2)

Water + sand, particle size <0.1 mm (0.004 in)

1.5 (4.9)

For more permanent installations with a heavily contaminated pumped liquid, a settling
pump-sump is recommended.

4  Installation

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

15

Содержание Flygt 2190









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды