manualshive.com logo in svg

Xylem Flygt 2190, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2190 Скачать руководство пользователя страница 43

Product code

Pressure class

Open or closed impeller

2201.691

MT, HT

Open

1. Prepare the shaft:

a) Polish off any flaws with a fine emery cloth.

The end of the shaft must be clean and free from burrs.

b) Clean and grease all sealing surfaces and O-rings.

Do not use molybdenum disulphide (MoS

2

).

c) Grease the end of the shaft and the impeller hub.
d) Insert the key in the keyway of the shaft.
e) Fit an appropriate number of adjusting washers on the shaft.

WS001820A

2. Check that the driving pin on the outer seal aligns with the key.
3. Without turning the shaft in relation to the driving ring, push the impeller carefully so

that the pin fits into the impeller keyway.

WS001819A

4. Fit the washer and the nut.
5. Tighten the impeller nut.

Tightening torque: 200 Nm (150 ft-lb)

6. Secure with washer.
7. Check that the impeller can rotate freely.

6.4.6  Install the impeller, alternative 2

Table 8: Applicability

Product code

Pressure class

Open or closed impeller

2190.010

HT

Closed

2201.012

HT

Closed

1. Prepare the shaft:

a) Polish off any flaws with a fine emery cloth.

6  Maintenance

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

41

Содержание Flygt 2190









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды