manualshive.com logo in svg

Xylem Flygt 2190, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2190 Скачать руководство пользователя страница 10

2  Transportation and Storage

2.1  Inspect the delivery

2.1.1  Inspect the package

1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. File a claim with the shipping company if anything is out of order.

If the product has been picked up at a distributor, make a claim directly to the
distributor.

2.1.2  Inspect the unit

1. Remove packing materials from the product.

Dispose of all packing materials in accordance with local regulations.

2. Inspect the product to determine if any parts have been damaged or are missing.
3. If applicable, unfasten the product by removing any screws, bolts, or straps.

For your personal safety, be careful when you handle nails and straps.

4. Contact the local sales representative if there is any issue.

2.2  Transportation guidelines

Precautions

DANGER: Crush Hazard

Moving parts can entangle or crush. Always disconnect and lock out power before
servicing to prevent unexpected startup. Failure to do so could result in death or serious
injury.

Position and fastening

The unit can be transported either horizontally or vertically. Make sure that the unit is
securely fastened during transportation, and cannot roll or fall over.

2.2.1  Lifting

Always inspect the lifting equipment and tackle before starting any work.

WARNING: Crush Hazard

1) Always lift the unit by its designated lifting points. 2) Use suitable lifting equipment and
ensure that the product is properly harnessed. 3) Wear personal protective equipment. 4)
Stay clear of cables and suspended loads.

NOTICE:

Never lift the unit by its cables or hose.

2.3  Temperature ranges for transportation, handling and storage

Handling at freezing temperature

At temperatures below freezing, the product and all installation equipment, including the
lifting gear, must be handled with extreme care.
Make sure that the product is warmed up to a temperature above the freezing point
before starting up. Avoid rotating the impeller/propeller by hand at temperatures below
the freezing point. The recommended method to warm the unit up is to submerge it in the
liquid which will be pumped or mixed.

2  Transportation and Storage

8

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

Содержание Flygt 2190









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды