Xylem Flygt 2190 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 72

background image

DANGER: Explosion/Fire Hazard

Special rules apply to installations in explosive or flammable atmospheres. Do not install
the product or any auxiliary equipment in an explosive zone unless it is rated explosion-
proof or intrinsically-safe. If the product is EN/ATEX-, MSHA- or FM-approved, then see
the specific EX information in the Safety chapter before taking any further actions.

Three thermal contacts are incorporated in the stator. They are normally closed.
Thermal contacts must never be exposed to voltages higher than 250 V, breaking current
maximum 6 A at a power factor 0.6. It is recommended that the thermal contacts are
connected to 24 V over a separate fuse to protect any other automatic equipment.

4.2.3 Connect the motor cable to the pump: Version code 590/690/691

5

92

93

90

WS002604C

Position number

Description

5

Hexagon head screw

90

Cable entry

92

Gland flange

93

Seal sleeve

Figure 9: Cable entry

WS008620A

1

2

Position

number

Description

1

Minimum clearance

3.2 mm (0.13 in)

2

Cable strain relief

Figure 10: Cable strain relief

1. Insert the motor cable.

25–30 mm (0.9–1.2 in) of the jacket must be on the inside of the cover.

2. Check that the seal sleeves and washers conform to the outside diameter of the cable.
3. Tighten the cable entry so that the seal sleeve is compressed and seals between the

motor cable and the cover.
Leave a clearance between the cover and the flange on the cable entry. See

10: Cable strain relief

(page 22).

The cable entry is threaded with Pg29/Pr37, Pg36/Pr47, and Pg42/Pr54.

4. Twist together the ground (earth) leads into a bundle and slip an insulating tube over

the intertwined leads.
The ground (earth) leads are located concentrically around each phase lead.

5. Fit the gland flange:

4 Installation

22

Flygt 2190, 2201 Installation, Operation, and Maintenance Manual

«
...
22
23
24
25
26
...
»

Содержание Flygt 2190









































































Отзывы:

Нет отзывов

Похожие инструкции для Flygt 2190

Бренд: YAMADA Страницы: 14

45 E Frame Series

Бренд: Danfoss Страницы: 44

ElectriFLEX LD LE Series

Бренд: Bradford White Страницы: 40

Бренд: Osram Страницы: 8

Бренд: OLIJU Страницы: 28

Бренд: RainWater Harvesting Страницы: 3

Бренд: Daikin Страницы: 316

Бренд: Magic-Pak Страницы: 18

Бренд: Pattfield Ergo Tools Страницы: 162

Бренд: Unitary products group Страницы: 16

Inverter Design

Бренд: Thermia Страницы: 16

Бренд: Daikin Страницы: 44

Taro Pumps NCH 2250

Бренд: Texmo Industries Страницы: 34

PACIFIC HYDROSTAR 1/3 HP Submersible Sump Pump with Vertical Float...

Бренд: Pacific hydrostar Страницы: 9

Бренд: Daesung Celtic Страницы: 62

Бренд: Goodman Страницы: 9

Бренд: Alpha-InnoTec Страницы: 40

Бренд: Graco Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды