Xylem CentiPro Aquavar IPC Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 36

background image

PAGE 31

Aquavar IPC Start-Up Genie

CentriPro

AQUAVAR IPC Q&A (AQIPCQA)

1. QUESTION

Where is the drive information, such as model
number and serial numbers located?

1. ANSWER

The Aquavar® Intelligent Pump Controller
identification label is located directly on top of the
drive. It is a good practice to locate this label and
record it, either by hand or with storing a digital
image. In the event that there are any issues with
initial delivery and startup, this information is going
to be required. It is also required in the event of
a warranty. There are also specific labels on the
outside of the carton it was delivered in.

2. QUESTION

Is there a simpler way to setup and configure this
controller?

2. ANSWER

There is a startup guide (AQUAVAR IPC Single Pump
Installation and Start-Up Instructions - IM283) with
wiring, programming, and illustrations to help you
get it up and running effortlessly. It is located on our
website:

http://documentlibrary.xylemappliedwater.com/
wp-content/blogs.dir/22/files/2015/07/AquavarIPC_
CentriPro_SinglePump_IM283_3-2017.pdf

3. QUESTION

In my Quick menu in #4, I do not see the startup
Genie. I only see the Smart Start.

3. ANSWER

You may have changed this accidentally during
intimal programming. Go into the Main Menu, Select
0 Operation/Display, and Select 0-0 basic Settings,
and 0-01 Language. If you see (0) English, change
this to (122 ENGLISH US). Go back into the Quick
Menu and #4 should list the Start Up Genie.

4. QUESTION

Can the IPC run more than one pump?

4. ANSWER

The IPC can operate in duplex mode (two pumps
maximum) providing lead/lag functionality as well
as alternation, just like the CPC product. If the lead
pump fails, the lag pump automatically comes on.
It does not have to be manually turned on. Both
IPC’s have to have their own PSI Transducer. Use the
Duplex Startup Guide: Aquavar® IPC Quick Start-Up
Instructions for Duplex Commissioning

http://documentlibrary.xylemappliedwater.com/
wp-content/blogs.dir/22/files/2016/09/IMAQIPC_
QuickStartUpInstr.pdf

5. QUESTION

What is different with the IPC duplex operation vs. a
CPC duplex operation?

5. ANSWER

Duplex operation in the IPC is done by the analog
signals between the two drives. This requires
additional wiring between the IPC. You can buy a
3 foot (9K706) or 6 foot (9K707) connection cable
to simplify your wiring. The included harness also
included a color coded wiring manual (9K267). Also
remember that the IPC can do a maximum of two
drives and the CPC up to four.

«
...
29
30
31
32
33
...
»

Содержание CentiPro Aquavar IPC





































Отзывы:

Нет отзывов

Похожие инструкции для CentiPro Aquavar IPC

Бренд: KAR-TECH Страницы: 28

Бренд: 2M Technology Страницы: 17

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: Baby Trend Страницы: 24

Бренд: Baby Trend Страницы: 6

Бренд: Baby Trend Страницы: 6

Бренд: C3 Custom Coolers Страницы: 16

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: BabySafe Страницы: 24

Бренд: Gardena Страницы: 16

Бренд: MADRIX Страницы: 28

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: Saitek Страницы: 15

Бренд: saia-burgess Страницы: 203

Бренд: Sailor Страницы: 1

Бренд: Xilinx Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды