XVision XSD10Z-2 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

background image

4

3. Installation

3.1 CONTENTS

z

XSD10Z-2 Dome

z

Installation Bracket

z

2.5mm Flat Head Screw Driver

3.2 INSTALLATION
1.

Dismantle the lower cover components of the transparent dome cover with Allun Key

2.

Drill holes in the ceiling according to the mounting hole position and install the plastic anchor.

3.

Feed the control cable, video cable and power cable through the ceiling

4.

Fix the dome base and the transparent dome cover, screw tightly to complete the installation as shown below.

3.3 WALL MOUNTING GUIDE

NOTE: THE WALL MOUNT IS NOT SUPPLIED WITH THE XSD10Z-2.

1.

Drill holes on the wall using the mounting hole position, and install the plastic anchor to the wall mount.

2.

Feed the control cable, video cable and power cable through the wall bracket cavity

3.

Align the dome camera to the bracket’s holes then rotate the dome camera clockwise and fix the backstop screw.

4.

Feed the control cable, video cable and power cable through the wall hole and fix the bracket using the screws and wall
plugs supplied.

Installation Holes

114mm

50mm

Ø=150mm

z

Allun Key

z

Opening Tool

z

4x Wall Plugs and Screws - for ceiling mount

Wall Bracket Installation Holes

12mm

6mm

Ø=137mm

120°

«
...
2
3
4
5
6
...
»

Содержание XSD10Z-2

























Отзывы:

Нет отзывов

Похожие инструкции для XSD10Z-2

Бренд: Canon Страницы: 60

Бренд: AccuBANKER Страницы: 2

Бренд: Major tech Страницы: 4

Бренд: Garrecht Avionik Страницы: 43

Бренд: M-system Страницы: 3

Бренд: CADDX Страницы: 6

Бренд: Hafele Страницы: 57

Бренд: Qvis Страницы: 44

LUXOMAT PD4-S-GH

Бренд: B.E.G. Страницы: 4

Бренд: Arecont Vision Страницы: 2

Бренд: Axis Страницы: 2

Бренд: Axis Страницы: 2

Бренд: nedis Страницы: 68

Бренд: Fike Страницы: 4

NEXT PLUS Series

Бренд: Visonic Страницы: 4

JV-B765HV9V22DNR

Бренд: JV vision Страницы: 12

Бренд: NAPCO Страницы: 4

Бренд: nclebo Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды