Xilinx Versal ACAP CPM4 Скачать руководство пользователя страница 91

Страница: 91 / 288

Table 29: Sideband Signals in pcie(n)_m_axis_rc_tuser (1024-bit Interface) (cont'd)

Bit Index

Name

Width

Description

167:160

is_eop[7:0]

Signals that one or more TLPs are ending in this beat only

when straddle is enabled. These outputs are set in the final

beat of a TLP. The settings are as follows:

•

00000000: No TLPs ending in this beat.

•

00000001: A single TLP is ending in this beat.

is_eop0_ptr[3:0] provides the offset of the last Dword of

this TLP.

•

00000011: Two TLPs are ending in this beat.

is_eop0_ptr[3:0] provides the offset of the last Dword of

the first TLP and is_eop1_ptr[3:0] provides the offset of

the last Dword of the second TLP.

•

00000111: Three TLPs are ending in this beat.

is_eop0_ptr[3:0] provides the offset of the last Dword of

the first TLP, is_eop1_ptr[3:0] provides the offset of the

last Dword of the second TLP, and is_eop2_ptr[3:0]

provides the offset of the last Dword of the third TLP.

•

00001111: Four TLPs are ending in this beat.

is_eop0_ptr[3:0] provides the offset of the last Dword of

the first TLP, is_eop1_ptr[3:0] provides the offset of the

last Dword of the second TLP, is_eop2_ptr[3:0] provides

the offset of the last Dword of the third TLP, and

is_eop3_ptr[3:0] provides the offset of the last Dword of

the fourth TLP.

•

00011111: Five TLPs ending in this beat, at locations

determined by is_eop0_ptr[4:0], is_eop1_ptr[4:0],

is_eop2_ptr[4:0], is_eop3_ptr[4:0] and is_eop4_ptr[4:0],

respectively.

•

00111111: Six TLPs ending in this beat, at locations

determined by is_eop0_ptr[4:0], is_eop1_ptr[4:0],

is_eop2_ptr[4:0], is_eop3_ptr[4:0], is_eop4_ptr[4:0] and

is_eop5_ptr[4:0], respectively.

•

01111111: Seven TLPs ending in this beat, at locations

determined by is_eop0_ptr[4:0], is_eop1_ptr[4:0],

is_eop2_ptr[4:0], is_eop3_ptr[4:0], is_eop4_ptr[4:0],

is_eop5_ptr[4:0] and is_eop6_ptr[4:0], respectively. .

•

11111111: Eight TLPs ending in this beat, at locations

determined by is_eop0_ptr[4:0], is_eop1_ptr[4:0],

is_eop2_ptr[4:0], is_eop3_ptr[4:0], is_eop4_ptr[4:0],

is_eop5_ptr[4:0], is_eop6_ptr[4:0] and is_eop7_ptr[4:0],

respectively.

•

All other settings are reserved.

When the straddle option is disabled, pcie(n)_m_axis_rc_tlast

indicates the final beat of a TLP.

172:168

is_eop0_ptr[4:0]

Offset of the last Dword of the first TLP ending in this beat.

This output is valid when is_eop[0] is asserted.
This output is used only when the straddle option is enabled

on the RC interface. The output is permanently set to 0

when straddle is disabled.

177:173

is_eop1_ptr[4:0]

Offset of the last Dword of the second TLP ending in this

beat. This output is valid when is_eop[1] is asserted.
This output is used only when the straddle option is enabled

on the RC interface. The output is permanently set to 0

when straddle is disabled.

Chapter 3: Product Specification

PG346 (v3.3) November 16, 2022

www.xilinx.com

CPM Mode for PCI Express

Send Feedback

Содержание Versal ACAP CPM4

































































































































































































































































































Результаты поиска

Содержание Versal ACAP CPM4

Отзывы:

Бренды по названию

Популярные бренды

Xilinx Versal ACAP CPM4, Руководство по эксплуатации продукта

Результаты поиска

Содержание Versal ACAP CPM4

Отзывы:

Бренды по названию

Популярные бренды