manualshive.com logo in svg

Xilinx Versal ACAP CPM4, Руководство по эксплуатации продукта

Поделиться
Скачать
Xilinx Versal ACAP CPM4 Скачать руководство пользователя страница 109

• Set the configuration space.

• Indicate if a correctable or uncorrectable error has occurred.

• Set the device serial number.

• Set the downstream bus, device, and function number.

• Receive per function configuration information.

This interface also provides handshaking between the user application and the core when a
Power State change or function level reset occurs.

Note: The 

pcie0*

 signals map to PCIe Controller 0 and 

pcie1*

 signals map to PCIe Controller 1 in the

port descriptions below.

Table 39: Configuration Control Interface Port Descriptions

Port

I/O

Width

Description

pcie0_cfg_hot_reset_in
pcie1_cfg_hot_reset_in

I

1

Configuration Hot Reset In
In RP mode, assertion transitions LTSSM to hot reset

state, active-High.

pcie0_cfg_hot_reset_out
pcie1_cfg_hot_reset_out

O

1

Configuration Hot Reset Out
In EP mode, assertion indicates that EP has transitioned

to the hot reset state, active-High.

pcie0_cfg_power_state_change_ack
pcie1_cfg_power_state_change_ack

I

1

Configuration Power State Ack
You must assert this input to the core for one cycle in

response to the assertion of

pcie(n)_cfg_power_state_change_interrupt, when it is

ready to transition to the low-power state requested by

the configuration write request. The user application

can permanently hold this input High if it does not

need to delay the return of the completions for the

configuration write transactions, causing power-state

changes.

pcie0_cfg_power_state_change_interrupt
pcie1_cfg_power_state_change_interrupt

O

1

Power State Change Interrupt
The core asserts this output when the power state of a

physical or virtual function is being changed to the D1

or D3 states by a write into its Power Management

Control register. The core holds this output High until

the user application asserts the

pcie(n)_cfg_power_state_change_ack input to the core.

While pcie(n)_cfg_power_state_change_interrupt

remains High, the core does not return completions for

any pending configuration read or write transaction

received by the core. The purpose is to delay the

completion for the configuration write transaction that

caused the state change until the user application is

ready to transition to the low-power state. When

pcie(n)_cfg_power_state_change_interrupt is asserted,

the function number associated with the configuration

write transaction is provided on the

pcie(n)_cfg_ext_function_number[7:0] output. When the

user application asserts

pcie(n)_cfg_power_state_change_ack, the new state of

the function that underwent the state change is

reflected on pcie(n)_cfg_function_power_state (for PFs)

or the pcie(n)_cfg_vf_power_state (for VFs) outputs of

the core.

Chapter 3: Product Specification

PG346 (v3.3) November 16, 2022

 

www.xilinx.com

CPM Mode for PCI Express

 109

Send Feedback

Содержание Versal ACAP CPM4

































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды