Xilinx Versal ACAP CPM4 Скачать руководство пользователя страница 78

Страница: 78 / 288

Table 24: Completer Completion Interface Port Descriptions (1024-bit Interface)

(cont'd)

Name

I/O

Width

Description

pcie0_s_axis_cc_tready

pcie1_s_axis_cc_tready

Activation of this signal by the PCIe core indicates that it is

ready to accept data. Data is transferred across the interface

when both pcie(n)_s_axis_cc_tvalid and

pcie(n)_s_axis_cc_tready are asserted in the same cycle.
If the core deasserts the ready signal when the valid signal

is High, the user logic must maintain the data on the bus

and keep the valid signal asserted until the core has

asserted the ready signal.
With this output port, each bit indicates the same value, so

the user logic can use any of the bit.

Table 25: Sideband Signals in pcie(n)_s_axis_cc_tuser

Bit Index

Name

Width

Description

3:0

is_sop[3:0]

Signals the start of a new TLP in this beat. These outputs are

set in the first beat of a TLP. When straddle is disabled, only

is_sop[0] is valid. When straddle is enabled, the settings are

as follows:

•

0000: No new TLP starting in this beat.

•

0001: A single new TLP starts in this beat. Its start

position is indicated by is_sop0_ptr[1:0].

•

0011: Two new TLPs are starting in this beat.

is_sop0_ptr[1:0] provides the start position of the first

TLP and is_sop1_ptr[1:0] provides the start position of

the second TLP.

•

0111: Three new TLPs are starting in this beat.

is_sop0_ptr[1:0] provides the start position of the first

TLP, is_sop1_ptr[1:0] provides the start position of the

second TLP and is_sop2_ptr[1:0] provides the start

position of the third TLP

•

1111: Four new TLPs are starting in this beat.

is_sop0_ptr[1:0] provides the start position of the first

TLP, is_sop1_ptr[1:0] provides the start position of the

second TLP, is_sop2_ptr[1:0] provides the start position

of the third TLP and is_sop3_ptr[1:0] provides the start

position of the fourth TLP

•

All other values: Reserved.

This field is used by the core only when the straddle option

is enabled. When straddle is disabled, the core uses tlast to

determine the first beat of an incoming TLP.

5:4

is_sop0_ptr[1:0]

Location of first SOP in the beat:

•

00: Byte lane 0

•

01: Byte lane 32

•

10: Byte lane 64

•

11: Byte lane 96

7:6

is_sop1_ptr[1:0]

Location of second SOP in the beat:

•

00:Reserved

•

01: Byte lane 32

•

10: Byte lane 64

•

11: Byte lane 96

Chapter 3: Product Specification

PG346 (v3.3) November 16, 2022

www.xilinx.com

CPM Mode for PCI Express

Send Feedback

Содержание Versal ACAP CPM4

































































































































































































































































































Результаты поиска

Содержание Versal ACAP CPM4

Отзывы:

Бренды по названию

Популярные бренды

Xilinx Versal ACAP CPM4, Руководство по эксплуатации продукта

Результаты поиска

Содержание Versal ACAP CPM4

Отзывы:

Бренды по названию

Популярные бренды