Selecting Driver Options/Defaults (for Windows)
17
Selecting Driver Options/Defaults
(for Windows)
Before you start working with your printer, you are advised to verify/change
the default driver settings. Also, in case you have options installed, you
should enable the options in the driver.
Windows XP/Server 2003/2000/NT 4.0
1
Choose the driver’s properties as follows:
(Windows XP/Server 2003)
From the
Start
menu, choose
Printers and Faxes
to display the
Printers and Faxes
directory. Right-click the Phaser 6120 PostScript
or Phaser 6120 PCL6 printer icon and choose
Properties
.
(Windows 2000/NT 4.0)
From the
Start
menu, choose
Settings
, and then
Printers
to display
the
Printers
directory. Right-click the Phaser 6120 PostScript or
Phaser 6120 PCL6 printer icon and choose
Properties
.
2
If you have installed options, proceed with the next step. Otherwise, skip
to step 9.
3
Select the
Configure
tab.
4
Check that the installed options are correctly listed. If not, proceed with
the next step. Otherwise, continue with step 8.
5
Click the
Refresh
button to automatically configure installed options.
"
The
Refresh
button is available only if bi-directional
communication is available with the printer; otherwise it is
grayed out.
6
From the
Device Option
list, select an option, one at a time, and then
select
Enable
or
Disable
from the
Settings
drop-down list.
"
If
Printer Memory
is selected, select
128 MB
,
256 MB
,
384 MB
or
640 MB
, according to the installed memory. The factory default
setting is
128 MB
.
7
Click
Apply
.
"
Depending on the version of the operating system,
Apply
may not
appear. If this is the case, continue with the next step.
"
With Windows NT 4.0, right-click the Phaser 6120 PostScript or
the Phaser 6120 PCL6 printer icon in the Printers directory, and
then click
Document Defaults
. Skip to step 10.
8
Select the
General
tab.
Содержание Phaser 6120
