Xembedded XVME-689-VR7 Скачать руководство пользователя страница 62

Страница: 62 / 94

BIOS Setup Menus

3-25

Option

Description

System Resources

This read-only field displays the status (Enabled or Disabled) of the XVME-661 system
resources. This value is automatically detected.

BERR Timeout*

This field is used to set the VMEbus error timeout. Choices are 16

s, 32

s, 64

(default), 128

s, 256

s, 512

s, 1024

s, and Disabled.

Arbitration Mode*

This field is used to set the VMEbus arbitration mode. Choices are Priority/Single
(default) or Round Robin.

*Note

These fields are only referenced if the board is the system controller. If it
is not, the setup field values are ignored,

BERR Timeout

is set to

Disabled

(0), and

Arbitration Mode

is set to

Round Robin

, with an Arbitration

timeout value of 0 (

Disabled

Содержание XVME-689-VR7































































































Результаты поиска

Содержание XVME-689-VR7

Отзывы:

Похожие инструкции для XVME-689-VR7

Бренды по названию

Популярные бренды

Xembedded XVME-689-VR7, Руководство пользователя

Результаты поиска

Содержание XVME-689-VR7

Отзывы:

Похожие инструкции для XVME-689-VR7

Бренды по названию

Популярные бренды