Xembedded XVME-689-VR7 Скачать руководство пользователя страница 15

Страница: 15 / 94

Introduction

1-8

Hardware Specifications

Characteristic

Specification

Power Specifications:

5.4 A (typical); 10.5 A (maximum)

Voltage Specifications:

+5V, +12V, -12V; all +5%/-2.5%

CPU speed: Intel Celeron M Low Power
Processor

1.8 GHz

L2 Cache: Intel Celeron M Low Power Processor

2 MB

Onboard memory

SDRAM, up to 2 GB (one 200-pin SODIMM)

Integrated Graphics Controller

1600 x 1200 maximum resolution, 24-bit color maximum; 4 MB
Shared memory

Ethernet Controllers (2)

Intel 82546GB 10/100/1000Base-TX Gigabit Ethernet; RJ-45

Mass Storage

Integrated SATA-150 Controller

SATA0 and SATA1 via P2

EIDE Ultra DMA 100 interface

2 channels via P2

One 1.8" on-board EIDE via optional carrier module

Compact Flash

One, on-board Compact flash site via optional carrier module

Floppy Drive

Via P2 to XVME 977

PMC Site

On board 66 MHz/64 Bit PMC/PCI-X with front and P0 I/O Access.
Site is 3.3V interface level

Optional 32bit / 33 MHz sites available via XVME-976-209 (2 sites,
total 3) and XVME-976-210 (4 sites, total 5)

Stereo Audio

AD1981B AC97 CODEC, Line Level Stereo Input and Output Via
P2

USB

One USB 2.0 via Front panel

Two USB 2.0 via P2

Serial Ports

RS-232C, 16550 compatible (4) COM1 Front, Com 2 and 3 Rear
I/O, (Com 4 can be configured for RS-232/422/485 but only the
COM 4 out the P2, Com 2 and 3 are RS-232 only). The COM 4 out
the front is RS-232 data leads only.

Parallel Interface

EPP/ECP compatible (1)

Keyboard and Mouse

Via Front Panel

European Union – CE;

Regulatory Compliance

Electromagnetic Compatibility - 89/336/EEC
RoHS Compliant product available

Содержание XVME-689-VR7































































































Результаты поиска

Содержание XVME-689-VR7

Отзывы:

Похожие инструкции для XVME-689-VR7

Бренды по названию

Популярные бренды

Xembedded XVME-689-VR7, Руководство пользователя

Результаты поиска

Содержание XVME-689-VR7

Отзывы:

Похожие инструкции для XVME-689-VR7

Бренды по названию

Популярные бренды