Xembedded XVME-689-VR7 Скачать руководство пользователя страница 90

Страница: 90 / 94

0 Appendix A SDRAM and Battery Installation

Appendix A SDRAM and Battery Installation

Memory Type

The XVME 689-VR7 has one 200-pin DDR333 SDRAM memory module (SODIMM) site in
which memory is inserted.

The XVME 689-VR7 supports 256MB, 512MB, 1MB and 2MB of PC2700 SDRAM.. Table A-1
lists the SODIMM configurations.

Table A-1 SDRAM SODIMM Configurations

Xembedded Part Number

Device Type and Size

Vendor

Vendor part number

200193

SODIMM 256MB DDR333

Micron

MT9VDDT3272HY-335F2

Virtium

VL485L3223C-B3

200194

SODIMM 512MB DDR333

Micron

MT9VDDT6472HY-335F2

Virtium

VL485L6523C-B3

200195

SODIMM 1GB DDR333

Micron

MT18VDDT12872HY-335F1

Virtium

VL485L2925C-B3

200196

SODIMM 2GB DDR333

Virtium

Installing SDRAM

Follow these steps to install the SODIMM:

Follow standard antistatic procedures using a wrist

strap to minimize the chance of damaging the
XVME 689-VR7 and its components.

Power off the XVME 689-VR7, remove it from the

VME backplane, and place it on a safe
antistatic (grounded) surface.

Remove all connectors if not already removed.

Locate the PX connector on the XVME 689-VR7

slightly in front of the P1 VME backplane
connector.

Pull the metal clips on either side of the SODIMM until it pops up at an angle (roughly 30

from horizontal).

Grasping the upper two corners or the edges of the SODIMM, gently pull it out of the socket

and set it to the side.

Insert the new SODIMM until seated into the connector assuring it fits snugly into the

connector retainer clips.

Содержание XVME-689-VR7































































































Результаты поиска

Содержание XVME-689-VR7

Отзывы:

Похожие инструкции для XVME-689-VR7

Бренды по названию

Популярные бренды

Xembedded XVME-689-VR7, Руководство пользователя

Результаты поиска

Содержание XVME-689-VR7

Отзывы:

Похожие инструкции для XVME-689-VR7

Бренды по названию

Популярные бренды