manualshive.com logo in svg

Xantrex Truecharge TC1012, Руководство по установке, Страница: 56 / 74

Поделиться
Скачать
Xantrex Truecharge TC1012 Скачать руководство пользователя страница 56

Installation

2–24

975-0402-01-01

This guide for use by qualified installers only

Installing Optional Accessories

Optional accessories are available for purchase at Xantrex. 
Call Customer Service to order the accessories below:

•

Remote Panel (Part number: 808-8040-00)

•

Battery Temperature Sensor (Part number: 808-0232-01)

Mounting the Optional Remote Panel

To mount the remote panel:

1. Choose a location for the remote panel that is within 

15 m (50 ft.) from the charger. Use only the four-
conductor communications cable (RJ-11) that came with 
the remote panel.

2. Use the enclosed mounting template to predrill mounting 

holes.
Take care that there is nothing behind the surface for you 
to damage such as other cables or pipes.

3. Connect the RJ-11 connector to the remote panel and 

route it to the charger. Be careful not to damage the 
connector locking tab when routing the cable. You can 
use some tape to protect the locking tab from catching on 
something and breaking off when routing the cable.

4. Once the Truecharge™ 2 Battery Charger is mounted, 

plug the other RJ-11 connector into the Remote port on 
the rear panel of the Truecharge™ 2 Battery Charger.

TC2 Series BattChg Install Guide.book  Page 24  Monday, June 30, 2008  3:18 PM

Содержание Truecharge TC1012











































































Отзывы:

Нет отзывов