Xantrex Truecharge TC1012 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 74

Xantrex Truecharge TC1012 Скачать руководство пользователя страница 5

iii

This guide for use by qualified installers only

About This Guide

Purpose

The purpose of this Installation Guide is to provide

explanations and procedures for installing and configuring
the Truecharge™ 2 Series Battery Charger.

Scope

The Guide provides safety guidelines, procedures for
installing the battery charger, as well as information on
configuring the battery charger. It does not provide details
about particular brands of batteries. You need to consult
individual battery manufacturers for this information.

Refer to Truecharge™ 2 Battery Charger Owner’s Guide
(doc. part number: 975-0401-01-01) for operational
instructions.

Audience

The Guide is intended for qualified installers who need to
install and configure any model unit of the Truecharge™ 2
Series Battery Charger. The installer should be a qualified
technician or electrician.

Organization

This Guide is organized into two chapters and one appendix.

Chapter 1 describes the standard features of a Truecharge™ 2
Battery Charger, as well as its protection features. It also
provides information on the different parts of the
Truecharge™ 2 Battery Charger including information on the
optional remote panel.

TC2 Series BattChg Install Guide.book Page iii Monday, June 30, 2008 3:18 PM

«
...
3
4
5
6
7
...
»

Содержание Truecharge TC1012











































































Отзывы:

Нет отзывов