manualshive.com logo in svg

Xantrex Truecharge TC1012, Руководство по установке, Страница: 17 / 74

Поделиться
Скачать
Xantrex Truecharge TC1012 Скачать руководство пользователя страница 17

Standard and Protection Features

975-0402-01-01

1–3

This guide for use by qualified installers only

The Truecharge™ 2 Battery Charger provides the following protec-
tion features: 

•

reverse polarity protection via an output fuse to guard 
against reverse battery polarity

•

AC input out-of-range protection shutdown

•

ambient over temperature protection shutdown

•

battery over-charging protection

•

electronic current limiting provides protection against 
short circuit conditions on the charger’s output 

•

ignition protected rating, enabling installation in engine 
spaces

•

isolated design

•

over temperature and short circuit protection for the BTS 
and communication connector ports

•

drip-proof rubber boots for DC terminals for added 
moisture protection

•

IP-32 drip protection rating

1

•

fan lockout protection

The optional Battery Temperature Sensor (BTS) provides these pro-
tection features:

•

battery under temperature charging protection preventing 
battery charging at -20 °C or below

•

charging current compensation for different battery 
temperatures

1.In two specific installation orientations–see “Truecharge™ 2 Battery Charger Mounting 
Orientations” on page 2–7.

TC2 Series BattChg Install Guide.book  Page 3  Monday, June 30, 2008  3:18 PM

Содержание Truecharge TC1012











































































Отзывы:

Нет отзывов