ECRESO FM 100/300 W, user manual– 06/2015
Page 87
Head Office : Parc d’activites Kennedy - 20, avenue Neil Armstrong – 33700 Bordeaux-Merignac (France)
Tel +33 (0)5 57 928 928 – Fax +33 (0)5 57 928 929 –
www.worldcastsystems.com – [email protected]
NAME
Access
(R/W)
Possible value on the serial
port of the unit
Comments
INPUT.LINE2.RIGHT.PEAK
R
-100 … 28
Gives the right audio input max peak value over 100
milliseconds
INPUT.LINE2.RIGHT.PKMAX
R
-100 … 28
Gives the right audio input max peak value over 1
second
INPUT.LINE2.SW.BACKDELAY
R/W
XXX=[0…30]
Back delay on the channel with the highest configurable
priority.
INPUT.LINE2.SW.NOSYNC
R/W
"ON" or "OFF"
If ON, switches on loss of AES synchro
INPUT.LINE2.SW.DELAY
R/W
XXX=[1…180]
Switching delay when loss of audio 2
INPUT.LINE2.SW.PRIO
R/W
0..7 ; 0=disabled
Priority of each audio channel (7= highest priority)
INPUT.LINE2.SW.SILENCE
R/W
"L" or "R" or "ANY" or "BOTH"
Sets on which channel silence detection must be
conducted for the audio input 2: L, R, L or R (ANY), L and
R (BOTH)
INPUT.LINE2.SW.THRESH
R/W
-90…000
Silence triggering level in dBFS on channel 2
INPUT.LINE2.TRIM
R/W
-3.00 to 3.00
Sets the offset between left and right channels (+3 = left
channel level is 3 dBu higher than right channel level)
INPUT.LINE2.TYPE
R
"ANA" or "AES" "OFF"
Indicates the type of audio signals present on input 2
INPUT.MPX.SW.BACKDELAY
R/W
XXX=[0…30]
Back delay on the channel with the highest configurable
priority.
INPUT.MPX.SW.DELAY
R/W
XXX=[1…180]
Switching delay when loss on the MPX input
INPUT.MPX1.ALARM
R/W
"NONE" or "FAULT" or
"WARNING"
Alarm generated upon loss of signal on the input
INPUT.MPX1.DRIVE
R/W
-6.00 to 6.00
Drive setting, allows an increase of the input audio level
without changing the deviation setting.
INPUT.MPX1.GET_SAMPLING
R
0…200000
Gives the sampling rate in Hz
INPUT.MPX1.LEVEL
R/W
-18.00...+18.00
Internal numerical gain
INPUT.MPX1.LOST
R
"YES" or "NO"
Detection of silence on the input after timeout. If ‘Yes’,
an alarm may be sent depending on the setting for
INPUT.MPX1.ALARM.
INPUT.MPX1.PEAK
R
-150…150
Gives the deviation max peak value of the transmitted
signal in kHz over 100 milliseconds
INPUT.MPX1.PKMAX
R
-150…150
Gives the deviation max peak value of the transmitted
signal in kHz over 1 second
INPUT.MPX1.PRESENCE
R
MO" or "MO+R" or "MO+R+S"
or "ST" or "ST+R" or "ST+R+S"
Gives the composition of MPX1 on channel 3. R = RDS ;
MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX1.SW.PRIO
R/W
0..7 ; 0=disabled
Priority of each audio channel (4= highest priority)
INPUT.MPX1.SW.THRESH
R/W
-90…000
Silence triggering level in dBFS
INPUT.MPX1.TYPE
R/W
"MO" or “ST” or “ST+R+S” or
“ST+R” or “RDS” or “RDS+SCA”..
Sets the signal type on the input and applies the
corresponding filter
INPUT.MPX1.TYPE
R/W
"MO" or "ST" or "ST+R+S" or
"ST+R" or "RDS" or "RDS+SCA"
or "SCA"
Sets the type of signal on the MPX1 input and applies
the corresponding filter
INPUT.MPX2.ALARM
R/W
"NONE" or "FAULT" or
"WARNING"
Alarm generated upon loss of signal on the input
INPUT.MPX2.DRIVE
R/W
-6.00...6.00
Drive setting, allows an increase of the input audio level
without changing the deviation setting.
INPUT.MPX2.GET_SAMPLING
R
0…200000
Gives the sampling rate in Hz
INPUT.MPX2.LEVEL
R/W
-18.00...+18.00
Internal numerical gain
INPUT.MPX2.LOST
R
"YES" or "NO"
Detection of silence on the input after timeout. If ‘Yes’,
an alarm may be sent depending on the setting for
INPUT.MPX2.ALARM.
INPUT.MPX2.PEAK
R
-150…150
Gives the deviation max peak value of the transmitted
signal in kHz over 100 milliseconds
INPUT.MPX2.PKMAX
R
-150...150
Gives the deviation max peak value of the transmitted
signal in kHz over 1 second
INPUT.MPX2.PRESENCE
R
MO" or "MO+R" or "MO+R+S"
or "ST" or "ST+R" or "ST+R+S"
Gives the composition of MPX2 on channel 3. R = RDS ;
MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX2.SW.PRIO
R/W
0..7 ; 0=disabled
Priority of each audio channel (4= highest priority)
