manualshive.com logo in svg

Woodpecker SPM 2-1000, Руководство по эксплуатации

Поделиться
Скачать
Woodpecker SPM 2-1000 Скачать руководство пользователя страница 26

 

 

 

BA_WP_SPM2-1000_EN_28-22.docx

 

26

 

6

 

Installation and Connection 

6.1

 

Check Delivery Conditions

 

Check the consignment for completeness and possible transport damage. In case of transport damage, please 
keep the packaging and inform the shipping company and the manufacturer immediately! Later complaints can-
not be accepted. 

6.2

 

Transport 

 

Lifting and transporting the machine must be carried out by qualified persons who have the required experi-
ence and equipment. 

 

Please take great care when loading and unloading the machine. The necessary measures 
must be taken to avoid impacts, damage as well as injuries to persons. When transporting, 
also pay attention to the existing danger of tipping over!

 

The machine is delivered on a transport pallet and is bolted to the bottom of the pallet. The centre of gravity of 
the machine is approximately in the middle of the pallet. The machine may only be transported using suitable 
aids, e.g. a forklift truck, lift truck or indoor crane with a load capacity sufficient for the weight of the machine 
(net weight approx. 400 kg). 

 

Danger to life under suspended loads during transport by forklift or crane. Staying under a 
suspended load is strictly prohibited! In addition, make sure that no objects fall down during 
transport by forklift / crane. Do not leave loose objects, accessories or tools on the machine.

 

6.2.1

 

Unloading with a Forklift Truck

 

 

 Figure 4: Unloading with a forklift truck  

 

Important! The forks of the forklift truck must be  
be at least 1200 mm long!

 

 

•

 

Move the forks of the forklift truck centrally between the pallet 
timbers.  

•

 

Then feed the forks of the forklift truck as shown in 

 Figure 4. 

•

 

Lift the pallet by a few centimetres and move the machine to 
the immediate vicinity of the installation site. 

 

6.2.2

 

Setting Down with a Forklift Truck 

 

 Figure 5: Setting down with a forklift truck 

 

Important! The forks of the forklift truck must be  

be at least 1200 mm long!

 

 

•

 

Remove  all  screw  fastenings  and  transport  locks  required  for 
transport on the pallet. 

•

 

Then lift the machine off the pallet with the forklift truck and 
feed the forks  as shown in 

  Figure 5. 

•

 

Now move the machine to the final installation site and park it 
at the final place of use.

 

 

 

Содержание SPM 2-1000























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды